Genuine Power Engineering- জেনুইন পাওয়ার ইন্জিনিয়ারিং

  • Home
  • Bangladesh
  • Dhaka
  • Genuine Power Engineering- জেনুইন পাওয়ার ইন্জিনিয়ারিং

Genuine Power Engineering- জেনুইন পাওয়ার ইন্জিনিয়ারিং ELECTRICAL PRODUCT

Perkins 2300/2500/2800 Series Engine Air pressure sensor
17/02/2021

Perkins 2300/2500/2800 Series Engine Air pressure sensor

Deep Sea (8610 MKII) are available in our stock.If you need, Please contact us for price quotation.
18/11/2020

Deep Sea (8610 MKII) are available in our stock.
If you need, Please contact us for price quotation.

Working area.....
05/11/2020

Working area.....

STOCK THIS PRODUCT
29/10/2020

STOCK THIS PRODUCT

Air Filter Efficiency - What Is It and How Is It Measured?We are often asked how well our air filters clean the air supp...
24/10/2020

Air Filter Efficiency - What Is It and How Is It Measured?

We are often asked how well our air filters clean the air supplied to the engine for combustion. This may be when customers are looking to improve their current air cleaner.

A common question is: "what micron rating is it?". However, a micron rating is an efficiency measurement used for liquid filters and not used for describing air filter efficiency.

Air filter elements are evaluated using an industry wide standard (ISO5011) and their performance is expressed as an efficiency level.

This efficiency level is determined by feeding air containing a known concentration of standard test dust into the air cleaner until the filter reaches the end of its life. This end of life is when the restriction reaches a predetermined level. The use of a standard test dust ensures consistency and is representative of the size range of dust particles found in real conditions.

When the filter reaches the end of its life, the weight of the dust on the filter is considered the capacity of the filter. Any dust, which passes the filter, is captured by an absolute filter down stream of the air cleaner in the test laboratory.

The weight of the dust captured by the absolute filter is compared to the weight of the dust fed into the air cleaner. The difference between them is the efficiency of the filter expressed as a percentage.

You May Like...

Servicing Your Air Filter – to Change or Not to Change?
While new Donaldson air filters provide good engine protection, a Donaldson air filter that has been in service for a period of time works even better than a new one.
The efficiency of an air filter will increase as dust accumulates on the filter surface, right up to the point at which it needs to be replaced. This is why it is important to allow an air filter to do its job properly and not change it prematurely. In other words, an air filter that is allowed to reach the end of its life will work better than filters that are changed more often.

Measuring the Percent of Particles Trapped by the Filter
These dust vials show the actual amount of fine test dust that passes through the air filter media for every one kilogram of dust fed to the air filter, which is equivalent to 100 hours* of equipment operation.
Donaldson Blue® Ultra-Web® HD Filter Media

Up to 99.999% Filtration Efficiency (0.01 gram dust)
Donaldson Blue® Ultra-Web® Filter Media

Up to 99.99% Filtration Efficiency (0.1 gram dust)
Donaldson Standard Filter Media

Up to 99.9% Filtration Efficiency (1 gram dust)
Will-fit Standard Filter Media

Up to 99.0% Filtration Efficiency (10 gram dust)
Will-fit filters can allow up to 100 times more dirt to pass through the filter into the engine than Donaldson Blue air filters with Ultra-Web filter media.
* Estimate based upon typical medium dust operating conditions with 92% pre-cleaner efficiency. Actual results may vary.


Did You Know?
Donaldson air filters in Donaldson air cleaner housings have a minimum overall efficiency greater than 99.90%. The efficiency of the filter actually improves as dust accumulates on the surface of the filter, so an air filter gets better as it gets used.

So how do you determine when the filter has reached the end of its life?

Don’t judge a filter by its appearance! The only practical way is to measure the restriction level, using a restriction indicator or gauge. All combustion engines are designed to operate with some restriction, and the manufacturer will specify the maximum acceptable level for their engine. This is the point at which you should change your filter. The condition of an air filter cannot be determined by its appearance.
Get the maximum protection for your engine and save money by allowing your air filter to work for its entire filter life.

How an oil filter worksThe oil filter helps remove contaminants from your car engine’s oil that can accumulate over time...
20/10/2020

How an oil filter works

The oil filter helps remove contaminants from your car engine’s oil that can accumulate over time as the oil keeps your engine clean.

The importance of clean motor oil
Clean motor oil is important because if the oil were left unfiltered for a period of time, it could become saturated with tiny, hard particles that can wear surfaces in your engine. This dirty oil can wear the oil pump’s machined components and damage the bearing surfaces in the engine.

How oil filters work
The outside of the filter is a metal can with a sealing gasket that allows it to be tightly held against the engine’s mating surface. The base plate of the can holds the gasket and is perforated with holes around the area just inside the gasket. A central hole is threaded to mate with the oil filter assembly on the engine block. Inside the can is the filter material, most frequently made from synthetic fiber. The engine’s oil pump moves the oil directly to the filter, where it enters from the holes in the perimeter of the base plate. The dirty oil is passed (pushed under pressure) through the filter media and back through the central hole, where it re-enters the engine.

Choosing the right oil filter
Choosing the correct oil filter for your vehicle is of the utmost importance. Most oil filters look very similar, but small differences in the threads or gasket size can determine whether or not a particular filter will work on your vehicle. The best way to determine which oil filter you need is by consulting your owner’s manual or by referencing a parts catalog. Using the wrong filter can cause oil to leak out of the engine, or an ill-fitting filter could just fall off. Either of these situations could lead to serious engine damage.

You get what you pay for
Generally speaking, the more money you spend the better the filter is. Lower-cost oil filters can contain light-gauge metal, loose (or shredding) filter material, and poor quality gaskets that can lead to failure of the filter. Some filters may filter out smaller bits of dirt a little better, and some may last longer. So, you should research the features of each filter that fits your vehicle to determine which one best fits your needs.

SCOPE OF WORK OF ACB SERVICING AND MAINTAINCE.Air Circuit BreakersCleaning of breaker with CRC-2261.Removal of old greas...
20/10/2020

SCOPE OF WORK OF ACB SERVICING AND MAINTAINCE.

Air Circuit Breakers

Cleaning of breaker with CRC-226
1.Removal of old grease and re-greasing the same with recommended grease.
2.Check condition of arcing contact and gap between fixed and moving arcing contacts shall be checked.
3.Checking the reset mechanism, tripping of breaker through push button
4.Checking tripping of ACB through protection release
5.Tripping of ACB manually through volt metric release.
6.Checking and adjust freeness of DN and volt metric release trip rod
7.Checking presence and proper tightening of hardware.
8.Checking presence of all circlips
9.Checking condition and alignment of jaw contact with cradle terminals
10.Checking condition of ACB wiring and replace if required
11.Checking and adjusting gap between hylam sheet and side plate
12.Checking proper closing of all poles together
13.Checking working of anti pumping device in case of EDO ACB
14.Checking alignment of SIC and it’s operation
15.Checking scrapping earth alignment
16.Checking condition of arc chutes
17.Checking U/V release pick up and drop off
18.Checking ACB tripping through shunt release
19.Checking motor operation in case of EDO ACB
20.Checking closing coil operation in case of EDO ACB
21.Checking continuity and proper changeover of aux contact block
22.Checking of release by secondary injection for O/L, S/C, E/F
Setting of release as per the load
23.Checking the healthiness of CTs
24.The spare parts, accessories would have to be provided by the customer.

Address

Tejgaon
Dhaka
1212

Website

Alerts

Be the first to know and let us send you an email when Genuine Power Engineering- জেনুইন পাওয়ার ইন্জিনিয়ারিং posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share