Tamturbo

Reittiohjeet Verkkosivusto Ota yhteyttä: Yritys

Tamturbo Tamturbo® Touch-Free™ turbo compressors: 100% oil-free, sustainable compressed air solutions.

Tamturbo is the Finnish pioneer of 100% oil-free turbo compressors and OEM turbo units. The result is sustainable, economical compressed air, with 20-30% lower total cost of ownership. Our team brings over 100 years of combined experience in the compressed air business, giving you uncomplicated access to oil-free turbo compressor technology through a growing global distributor network

A compressor almost never operates at exactly the load it was sized for. Compressed air demand is constantly fluctuating...
29/09/2026

A compressor almost never operates at exactly the load it was sized for.

Compressed air demand is constantly fluctuating throughout the day. Shifts change, lines start and stop, air use rises and falls with them. So the number that matters is not full-load efficiency on a datasheet. It is how efficient the machine stays when demand drops to 70 or 50 percent.

Many systems handle part load badly. A fixed-speed machine that unloads still draws power while making no air, and an oversized compressor spends much of its life in exactly that state.

This is where architecture decides the outcome. A Tamturbo compressor is directly driven and variable speed, on Touch-Free™ active magnetic bearings, with no gearbox and no mechanical contact. It modulates smoothly across a wide range instead of switching between load and idle.

The result is efficiency that tracks the real demand curve, not just a strong figure at one operating point.

For any plant where air demand varies, part load is usually where the energy cost is quietly won or lost.

Worth asking how a compressor performs across the whole load range, not only at its rated point.

𝗙𝗼𝗹𝗹𝗼𝘄 Tamturbo for more straight talk on efficiency, and 𝗮𝘀𝗸 𝗼𝘂𝗿 𝗲𝗻𝗴𝗶𝗻𝗲𝗲𝗿𝘀 to walk you through how the machine behaves at part load.

Over the past weeks, these posts have circled one idea from different angles: compressed air is treated as a fixed, invi...
24/09/2026

Over the past weeks, these posts have circled one idea from different angles: compressed air is treated as a fixed, invisible utility in most plants. It does not have to be.

We looked at where the air actually goes. Why oil-free at the source is different from oil-free after filtration. What part-load efficiency really means. How energy that is usually wasted can be recovered as heat. And why the cheapest compressor to buy is often the most expensive to own.

The thread through all of it is the same. Decisions made once, at the machine, set the cost and the cleanliness for the next ten years.

That is the work we care about at Tamturbo. 𝟭𝟬𝟬% 𝗼𝗶𝗹-𝗳𝗿𝗲𝗲 𝘁𝘂𝗿𝗯𝗼 𝗰𝗼𝗺𝗽𝗿𝗲𝘀𝘀𝗼𝗿𝘀, built in Tampere, Finland on Touch-Free™ technology, designed so that 𝗰𝗹𝗲𝗮𝗻 𝗮𝗶𝗿 𝗮𝗻𝗱 𝗹𝗼𝘄 𝗲𝗻𝗲𝗿𝗴𝘆 use come from the architecture of the machine, not from the chain of fixes around it.

If your plant runs on compressed air and these topics feel familiar, those are exactly the questions we like to get into.

So, a simple note to close on: what is the single biggest thing your plant could do better with compressed air?

𝗙𝗼𝗹𝗹𝗼𝘄 Tamturbo, 𝗯𝗿𝗼𝘄𝘀𝗲 𝘁𝗵𝗲 𝗿𝗲𝘀𝘁 𝗼𝗳 𝘁𝗵𝗲 𝘀𝗲𝗿𝗶𝗲𝘀, and visit our website to find the right person on our team to talk to.

One pattern shows up again and again when a plant switches to oil-free turbo compressors. The reason they bought it is r...
22/09/2026

One pattern shows up again and again when a plant switches to oil-free turbo compressors.

The reason they bought it is rarely the thing they talk about a year later.

Most start with air quality. A process that cannot tolerate oil, a tightening specification, an audit that flagged a contamination risk. That is the trigger for the project.

Then the system runs, and the conversation moves.

The maintenance team notices that the recycling, changing, and managing of oil tasks are gone.

The energy manager notices the load follows demand instead of fighting it. Finance notices the cost line that used to creep upward has flattened.

The clean-air requirement opened the door. The energy and maintenance profile is what they value once it is running.

It is a useful reminder for any utility decision. The headline reason for a purchase and the lasting source of value are not always the same thing, and the full picture only shows up over the operating life, not on the day of the decision.

If you have changed a major utility recently, did the real benefit turn out to be the one you expected?

𝗙𝗼𝗹𝗹𝗼𝘄 Tamturbo for more patterns from the field, and 𝗴𝗲𝘁 𝗶𝗻 𝘁𝗼𝘂𝗰𝗵 𝘄𝗶𝘁𝗵 𝗼𝘂𝗿 𝘁𝗲𝗮𝗺 when you are ready to compare.

𝗪𝗵𝗲𝗿𝗲 𝗱𝗼 𝘆𝗼𝘂 𝘁𝗵𝗶𝗻𝗸 𝗺𝗼𝘀𝘁 𝗼𝗳 𝘆𝗼𝘂𝗿 𝗰𝗼𝗺𝗽𝗿𝗲𝘀𝘀𝗲𝗱-𝗮𝗶𝗿 𝗺𝗼𝗻𝗲𝘆 𝗮𝗰𝘁𝘂𝗮𝗹𝗹𝘆 𝗴𝗼𝗲𝘀? 🔌 Energy to run the compressors 💨 Air lost through l...
17/09/2026

𝗪𝗵𝗲𝗿𝗲 𝗱𝗼 𝘆𝗼𝘂 𝘁𝗵𝗶𝗻𝗸 𝗺𝗼𝘀𝘁 𝗼𝗳 𝘆𝗼𝘂𝗿 𝗰𝗼𝗺𝗽𝗿𝗲𝘀𝘀𝗲𝗱-𝗮𝗶𝗿 𝗺𝗼𝗻𝗲𝘆 𝗮𝗰𝘁𝘂𝗮𝗹𝗹𝘆 𝗴𝗼𝗲𝘀?

🔌 Energy to run the compressors
💨 Air lost through leaks that never reach a tool
🛢️ Maintenance, oil, and consumables
🏭 Oversizing, so the system runs bigger than the plant needs

There is no single right answer. It depends on the site, the age of the system, and how closely anyone is watching. But the option people pick first usually says a lot about where their attention already sits, and the one they forget is often where the savings are hiding.

In a lot of plants, the honest answer is that nobody has measured it closely enough to know.

Drop your pick in the comments. One word is fine. We will gather what comes back and share the pattern in a follow-up, the same way we did with the last question.

𝗙𝗼𝗹𝗹𝗼𝘄 Tamturbofor the follow-up, and 𝗿𝗲𝗮𝗰𝗵 𝗼𝘂𝘁 𝘁𝗼 𝗼𝘂𝗿 𝘁𝗲𝗮𝗺 if you want help finding where your air money goes.

Janne Leinonen has started as CEO of Tamturbo.Janne brings extensive international leadership experience from industrial...
14/09/2026

Janne Leinonen has started as CEO of Tamturbo.

Janne brings extensive international leadership experience from industrial technology, including executive roles at ABB and senior leadership positions at global technology companies.

As CEO, Janne will lead Tamturbo's next phase of international growth and further strengthen our position as a pioneer in oil-free compressed air solutions for industrial applications worldwide.

“Tamturbo has developed a truly unique technology that delivers a superior Total Cost of Ownership compared to traditional compressor solutions. Our dedicated team is committed to helping customers achieve measurable savings through lower energy consumption, enhanced reliability, and long-term peace of mind. At the same time, our technology directly supports the global transition toward a more sustainable industrial future.”

The next chapter begins today. Together with our employees, customers, partners, and stakeholders, we are ready to accelerate growth and create lasting value through innovation and sustainability.
Read the full story on our website: www.tamturbo.com/news/janne-leinonen-starts-as-ceo-of-tamturbo

Two compressors sit in a tender. One is cheaper to buy. Over ten years, it can be the far more expensive choice. For a c...
10/09/2026

Two compressors sit in a tender. One is cheaper to buy. Over ten years, it can be the far more expensive choice.

For a compressor that runs most of the year, the purchase price is the smallest number in the lifetime total. Energy is the large one, paid every hour the machine runs. Maintenance, spare parts, and the value of any recovered energy sit on top.

That is why the owners who get this right read the whole lifetime cost, not the sticker. The cheapest machine to buy and the cheapest machine to own are often not the same machine.

This is the ground Tamturbo® is built for. 𝗡𝗼 𝗼𝗶𝗹, 𝗻𝗼 𝗴𝗲𝗮𝗿𝗯𝗼𝘅, and Touch-Free™ architecture designed to 𝗵𝗼𝗹𝗱 𝗶𝘁𝘀 𝗲𝗳𝗳𝗶𝗰𝗶𝗲𝗻𝗰𝘆 𝗼𝘃𝗲𝗿 𝘆𝗲𝗮𝗿𝘀 rather than lose it as it ages. Lower energy use in every running hour is what pulls the total cost of ownership down and keeps it down.

The honest comparison uses your numbers, not ours. Your running hours, your electricity price, your load profile, your heat demand. That is the only way to see the real total cost of ownership for your site.

That is exactly the calculation our sales team will build with you. Share your operating data and we will model the lifetime cost for your case, not a generic estimate.

The lowest price on the invoice is rarely the lowest cost over ten years. The only way to know is to put the lifetime numbers side by side.

𝗙𝗼𝗹𝗹𝗼𝘄 Tamturbo for more on the economics of compressed air, and 𝗮𝘀𝗸 𝗼𝘂𝗿 𝘀𝗮𝗹𝗲𝘀 𝘁𝗲𝗮𝗺 for a total cost of ownership calculation built on your own operating data.

Automotive and tire makers are pushing carbon targets down into their supply chain. If you supply them, their Scope 3 is...
08/09/2026

Automotive and tire makers are pushing carbon targets down into their supply chain. If you supply them, their Scope 3 is your Scope 1 and 2.

That changes how a utility like compressed air gets viewed. It stops being only an operating cost and it becomes part of the emissions number a customer will ask you to report, then reduce.

Compressed air is a good place to look, for one reason. It is often a large, steady electricity load, and its efficiency is mostly fixed by the machine you chose. A more efficient compressor lowers energy use every hour it runs, which lowers the bill and the emissions behind it together.

Two levers matter most: how efficiently the compressor runs across real demand, not just at full load, and whether the energy it produces is recovered or thrown away.

Neither is exotic. Both are decided once, at procurement, and then locked in for ten years or more.

For a supplier under pressure to show real reductions, the air system is one of the more controllable numbers on the list.

Is compressed air in your emissions plan yet, or still filed under utilities?

Follow Tamturbo for more on energy and emissions and talk to our team about getting compressed air into the plan.

“Oil-free compressed air” does not always mean an oil-free compressor. That distinction matters more than many specifica...
05/09/2026

“Oil-free compressed air” does not always mean an oil-free compressor.

That distinction matters more than many specifications suggest.

Many compressors sold as oil-free still contain oil inside the machine. It is used for bearings, gears, or seals, while downstream filtration keeps the delivered air within specification.

Clean air, achieved through filtration and maintenance discipline.

There is another approach.

With 𝗔𝗰𝘁𝗶𝘃𝗲 𝗠𝗮𝗴𝗻𝗲𝘁𝗶𝗰 𝗕𝗲𝗮𝗿𝗶𝗻𝗴𝘀, the shaft runs without mechanical contact. No bearing wear. No oil lubrication. No oil inside the compressor at all.

Then clean compressed air is a property of the machine architecture itself, not only of the filter chain around it.

The distinction is especially relevant where compressed air comes into contact with product or process: food, beverage, pharmaceuticals, electronics, and other contamination-sensitive applications.

There, the real question is not only whether the air is certified oil-free. It is whether the compressor itself contains oil at all.

That is the logic behind Tamturbo Touch-Free technology.

A small wording difference in a specification can mean a very different machine design, maintenance profile, and process-risk level over the life of the asset.

Worth checking in your next compressor specification review.

hashtag hashtag hashtag hashtag hashtag

Ask a maintenance team what a compressor really costs, and oil comes up fast. Oil changes. Oil analysis. Filter and sepa...
03/09/2026

Ask a maintenance team what a compressor really costs, and oil comes up fast.

Oil changes. Oil analysis. Filter and separator replacement. Disposal. And a planned stop for each one. On an oil-lubricated machine, that is normal, scheduled, and built into the service calendar.

Now picture the same utility without the list.

When the compressor has no oil and the shaft runs on Touch-Free™ active magnetic bearings, a whole class of maintenance tasks simply does not exist. No lubrication schedule. No oil-related bearing wear. No oil to sample, replace, or dispose of. On a Tamturbo unit the only regular consumable is the intake air filter.

That changes the service model. Fewer planned stops, fewer consumables, and one less thing to miss on a busy week.

For plants where downtime is expensive, the value is not only cleaner air. It is a quieter maintenance calendar and a more predictable cost line.

Reliability is rarely won with one big feature. It is won by removing the small, recurring things that go wrong.

What is the most frequent planned stop on your compressors today?

Follow Tamturbo for more from the service side, and contact our team if a quieter maintenance calendar would help.

In a tire plant, compressed air is one of the electricity loads that never really switches off.It shapes the green tire,...
01/09/2026

In a tire plant, compressed air is one of the electricity loads that never really switches off.

It shapes the green tire, holds the curing bladder, drives the tools, and moves material between steps. Hour after hour, shift after shift, all of it runs on air.

Which is why the cost that matters most is rarely the price of the compressor. It is the energy that the compressor will draw over the next ten years.

For a utility that runs this hard, lifecycle cost is dominated by electricity, and the machine architecture you pick sets that number. It is very hard to change once the unit is bolted down.

There is a second, quieter cost. If air quality is handled by filtration alone, you can pay for it twice: once for the filters and their upkeep, and again for the pressure drop and energy they add.

A compressor with 𝗻𝗼 𝗼𝗶𝗹 𝗶𝗻𝘀𝗶𝗱𝗲 and strong part-load efficiency narrows both. Clean air comes from the architecture, and energy use follows real demand instead of running flat out. Tamturbo Touch-Free™ compressors are 100% oil-free by design, so the air stays clean without a filter bank in the way.

The air still must be clean and dry to protect rubber quality. That part is not negotiable. The opening is meeting it without overpaying for energy for a decade.

So, the better question to ask in a tire plant is not only whether the air is clean enough. It is what that clean air costs to make, year after year.

Follow Tamturbo for more on the economics of compressed air, and talk to our team when you want to put real numbers on it.

Osoite

Menotie 1A
Ylöjärvi
33470

Verkkosivusto

Ilmoitukset

Saat tiedon ensimmäisenä: lähetämme sinulle sähköpostia, kun Tamturbo julkaisee uutisia ja tarjouksia. Sähköpostiosoitettasi ei käytetä muihin tarkoituksiin, ja voit perua tilauksen milloin tahansa.

Ota Yhteyttä: Yritys

Lähetä viesti: Tamturbo:

Oikopolut

Jaa

Kategoria