EMC Fabrication and Design

EMC Fabrication and Design AAS in Welding Technology. Class of 2019 at SPSCC. Welder/Fabricator for 10 years and counting! We specialize in all FWD SR20 Nissan chassis. Hi!

My name is Dylan and I can fabricate just about anything car and motorcycle related. From vintage restoration to performance parts fabricated from scratch. I have 9+ years of welding and fabrication experience, as well as an AAS Degree in Welding Technology from SPSCC. Feel free to browse through my build pictures and give me a call if you're next in line for a build of your own. Let your next mile be an Easy Mile.

An SR20 swapped 1960's Datsun Roadster...what a cool car to work on.This customer is doing this engine swap project most...
07/09/2026

An SR20 swapped 1960's Datsun Roadster...what a cool car to work on.

This customer is doing this engine swap project mostly himself, however he tasked me with building him a custom stainless turbo log manifold along with a custom stainless downpipe to go with it! So, he got what he asked for 🔥

Another fully TIG welded stainless exhaust in the books! Had the absolute pleasure to work on this beautiful 1969 Camaro...
06/03/2026

Another fully TIG welded stainless exhaust in the books! Had the absolute pleasure to work on this beautiful 1969 Camaro SS.

2.5" tubing all the way back, an in-house made x-pipe, dual magnaflow's, and a dual exit out the back with tucked away 45° tips.

Turned out fantastic, customer is stoked!

04/17/2026

In preparation for Import Face-Off in Kent, we will be closed April 22nd through the 26th. Wish us luck!

This job brought me out to Boyer Towing in Seattle! Fabbed up a couple stainless exhaust sections for some massive forkl...
04/15/2026

This job brought me out to Boyer Towing in Seattle! Fabbed up a couple stainless exhaust sections for some massive forklifts. Fully TIG welded 2.5" tube with some slip joints on each end. Turned out 🔥 as usual!

This customer brought in a set of aluminum fuel cells for his jet boat. Needed me to extend each cell about 2ft longer t...
04/13/2026

This customer brought in a set of aluminum fuel cells for his jet boat. Needed me to extend each cell about 2ft longer to allow more run time while he's out on the water. This one was a little tedious figuring out fit-up, but once that was done...welding was a breeze. Turned out great, and the customer is stoked!

This 2.5" fully TIG'd stainless exhaust turned out super cool. Another resto Chevy Impala. Incredibly stoked and gratefu...
03/07/2026

This 2.5" fully TIG'd stainless exhaust turned out super cool. Another resto Chevy Impala. Incredibly stoked and grateful that I had the opportunity to work on this absolute gem of a car.

This one is running Flowmaster HP-2's and has dual side exits with 3" oval tips that are slash cut parallel to the trim.

Can't wait to hear this thing fire up 🔥

First stainless exhaust job of the year! Super cool complete restomod Bel-Air. Even though this customer wanted a stainl...
02/14/2026

First stainless exhaust job of the year! Super cool complete restomod Bel-Air. Even though this customer wanted a stainless MIG'd exhaust, still turned out pretty slick. The tolerances on the mufflers to the frame were as tight as it gets...but still made it work. Used 2.5" tube, a handful of custom hangers for the mufflers, v-bands all the way around, and a plasma cut x-pipe brace to keep things snug without too much movement

We're starting to get busy again, so if you've got a project you need to get done soon...now is the time to do so.

It's finally finished! The last job I did for Bean Bags in Centralia after all of the stainless shelving, were two large...
02/13/2026

It's finally finished! The last job I did for Bean Bags in Centralia after all of the stainless shelving, were two large 42" circle signs laser cut with their logo. Probably about 2-3 months ago. They've finally been installed, so now I can post! These signs turned out so damn cool, and the back lighting idea just worked flawlessly.

Made out of 16 gauge mild, a little bit of structure to stiffen up the sign, and a 1" ring welded all the way around the back side for mounting the LED strips.

Definitely the best sign I've made to date.

We fabricate engine building tools! Specific to the SR20, this is a very common tool needed to properly measure the valv...
01/28/2026

We fabricate engine building tools! Specific to the SR20, this is a very common tool needed to properly measure the valve shim clearances when modifying the rockers to take dual guide shims. Machined out of 6061 aluminum.

This order just went out to Dallas, TX.

Thanks Tim!

Address

Elma, WA

Telephone

(360) 704-0840

Website

Alerts

Be the first to know and let us send you an email when EMC Fabrication and Design posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to EMC Fabrication and Design:

Shortcuts

Share

Category