What are the opening hours?

Monday 7am - 4:30pm Tuesday 7am - 4:30pm Wednesday 7am - 4:30pm Thursday 7am - 4:30pm Friday 7am - 3pm

FHS Poly

Name: FHS Poly
Address: 11/15 Martha Street, Seaford, VIC, 3198, AU
Telephone: +611300347111
Price range: Not Applicable

Call Directions Website Contact the business

FHS is an Australian owned company specialising in polyethylene fabrication services, and supply of pipe, fittings and plastic welding equipment.

14/10/2026

The part people underestimate either way is calibration. An uncalibrated welder puts every joint you've made into question, and on a spec job that's a real problem, not a paperwork one.

Hire gear comes out calibrated with documentation. Owned gear is on you.

We do both, and we'll tell you straight which one your situation calls for. Even when the answer is buy.

Not sure which way to go?

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01pL210
📧 [email protected]

12/10/2026

Two different jobs, two different tools, and using the wrong one is where sheet fabrication goes sideways.

Hot air gives you control for tacking, for thin sheet, for detail work and repairs in tight spots. Extrusion lays down the volume of material a structural weld in tank or liner work actually needs.

Most sheet fabrication jobs want both. Tack it up with hot air, run the structural weld with extrusion.

Our hire fleet covers both, including Munsch and Forsthoff gear, plus SuperFUSION weld rod matched to what you're joining. HDPE, PE100, PP, PVC and more.

Fabricating a tank, lining a pit, repairing a liner? Talk to us before you pick the machine.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01pL1B0
📧 [email protected]

08/10/2026

The bead on a poly pipe butt weld tells you plenty. Taking it off properly tells you more.

Remove the external bead cleanly and you can run a bend back check on it. Good fusion holds. Contamination or a cold joint shows up as a split between the beads. That's a QA check you can do on site, and it costs you nothing but the bead.

Then there's the flow side. Internal bead in a pressure main is a turbulence point and a collection point. On potable water and process lines, plenty of specs call for it gone.

Doing either of those with a knife and a grinder is slow, inconsistent and very difficult inside a pipe less than 800mm diameter.

Our debeader and trimmer hire range covers internal and external across the size range, so the tool matches the pipe rather than the other way around.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01pKZC0
📧 [email protected]

06/10/2026

The control unit is the cheapest part of a good electrofusion joint.

Most EF failures don't come from the box. They come from what happened before the box was plugged in. Oxidised surface left unpeeled. A peel that missed a section. Pipe that wasn't rerounded and wasn't clamped, so it moved mid-cycle.

That's why our EF hire doesn't stop at the control unit. Rotary peelers, rerounding and alignment clamps, 90% isopropyl wipes, generators sized to run the unit properly.
Even a datalogging solution that steps you through the process and records all the details you need to provide confidence to your customer that you know what youre doing!
Hire the process, not just the machine. It's the difference between a joint that passes and a joint you're cutting out next week.

What's the one EF prep step you see skipped most on site?

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01pK-B0
📧 [email protected]

02/10/2026

The Right Butt Welder for Every Job

Choose the Machine to Suit the Project
No single butt welder is suitable for every pipe size, welding method and worksite. Our Butt Weld Hire Fleet consists of a variety of electro-hydraulic machines.
The best choice depends on the pipe diameter, the required ISO 21307 welding method and the level of productivity needed on site.

Select by Welding Diameter
• 40–160 mm
• 63–250 mm
• 90–315 mm
• 90–355 mm
• 160–450 mm
• 315–630 mm
• 630–1200 mm

Choose High Force or Low Force Welding
High Force machines are designed to perform Single High Pressure welding in accordance with ISO 21307 and offer higher productivity through shorter weld cycles. Low Force ram machines are designed to perform Single Low Pressure welding in accordance with ISO 21307. The appropriate option will depend on the project specification, pipe size and required production rate.

Productivity and Handling Options
• Crane-assisted machines: Some larger-diameter butt welders have an attached crane to lift the facer and heater plate into the cradle, reducing manual handling during welding.
• Indexing facer and heater plates: Our high-end machines use facer and heater plates that swing into the weld zone on an arm as required, improving workflow and productivity.
• Trolley-type butt welders: These machines combine High Force rams, which can cut weld times by up to half, with swinging facer and heater plates. Mounted on wheels and towable, they can also be moved more easily around the job site.
• Tracked machines: For greater mobility on demanding job sites, self-powered tracked machines offer exceptional versatility and productivity. Their enhanced

Serviced, Calibrated and Ready to Work
Every machine is supplied serviced and calibrated, with current documentation. We match the machine’s diameter range, welding method and productivity features to the demands of your application.

Talk to Us About Your Project
Tell us your pipe sizes, SDR, project specification, required production rate and site conditions. We will recommend the most efficient and cost-effective butt welder for your project.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01pK-v0
📧 [email protected]

30/09/2026

Diameter shouldn't determine who you call. The Riyang Armor Trolley range covers 63mm through to 1200mm, all in one family of machines, so whatever's specified on your next job, there's a model built for it, without switching suppliers or systems.

Every model is built to ISO 21307 and ASTM F2620 high-pressure standards, and PE WeldBank compatible for full weld traceability, so documentation and compliance scale with the machine, not against it.

Talk to our team about which Armor Trolley model is right for your next project.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01nQlG0
📧 [email protected]

24/09/2026

Low pressure and high pressure butt fusion aren't just different intensities of the same process, they're two distinct, standard-defined procedures, each with its own pressure, temperature and time parameters.

ISO 21307 is explicit that once a method is chosen, its parameters must be followed as a complete set. Mixing pressure and times from the low and high pressure procedures on the same weld is definetly a 'big no no', and is easily avoidable on site these days with poly welding apps.

Getting the pressure level right at the start isn't only about buying the correct machine, it's what keeps your weld procedure defensible if a project is ever audited or a joint is ever questioned.

That's a conversation worth having with our team before the machine leaves the yard, not after the pipe's in the ground.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01nPZ30
📧 [email protected]

22/09/2026

The small gear that protects a big weld.

Pipe Rollers:
- DOLPHIN rollers (up to 355mm);
- MAMBA rollers (up to 630mm); and
- DRAGON rollers (up to 1200mm),
all made by Riyang, keep pipe properly supported and aligned throughout the weld, cutting down on the friction and misalignment that can undermine an otherwise good joint. So important!

And when weld beads need removing:
External debeaders:
- CONDOR 400 (110 - 400mm)
- CONDOR 800 (400–800mm)
made by Riyang, easily remove the new outside bead from large-diameter pipe after butt welding, leaving a clean finish without extra manual work.

Using the right tools makes the job soooo easy, but skip the essentials and it shows in the weld.

Ask us about kitting out your crew with the right accessories for the job.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01nPWr0
📧 [email protected]

08/09/2026

Low-pressure butt fusion isn't just "less pressure", it's a tried and true defined process delivering joints stronger than the pipe itself.

Per ISO 21307, low-pressure butt weld jointing runs at a set dynamic fusion pressure with heat soak time and cooling time calculated from wall thickness, and it requires a specific allowance for drag pressure (the resistance needed to move the pipe into position) to arrive at an accurate weld pressure. Get any of those figures wrong and you're looking at a cold or overpressurized weld, not just a slower cycle.

Riyang's Low Pressure butt welders are built to run that process correctly and repeatably - standard fusion pressure and cooling time, sized for the medium-to-large SDR, small-to-medium diameter pipe used in most distribution pipeline work. The range is compliant with ISO 21307 Low, DVS 2207, WIS 4-32-08 and NS-INSTA 2072-2, so the parameters are already validated against the standards your project needs to meet.

Not sure which pressure level your next job calls for? Our team can help you spec it correctly before you order.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01bqRp0
📧 [email protected]

03/09/2026

Not every job needs you to own the machine.

Small-diameter pipeline work still demands full fusion performance, but not every project justifies the capital outlay of owning a dedicated machine.

Meet the Riyang Armor 355: a compact, trailer-mounted butt fusion machine built for PE pipe up to 355mm diameter.

It rolls straight off the trailer and onto site which means no crane, no forklift, no additional lifting equipment required.

The same reliable fusion performance you'd expect from a full workshop setup, just on wheels and ready when you need it.

Now available for hire through FHS Poly. Minimum 2-week hire - call our team to check availability or book a demo.

📞 1300 347 111
🌐 https://ap1.hubs.ly/H01bqDj0
📧 [email protected]

Address

11/15 Martha Street
Seaford, VIC
3198

Opening Hours

Monday	7am - 4:30pm
Tuesday	7am - 4:30pm
Wednesday	7am - 4:30pm
Thursday	7am - 4:30pm
Friday	7am - 3pm

Telephone

+611300347111

Website

http://www.fhs.com.au/

Alerts

Be the first to know and let us send you an email when FHS Poly posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to FHS Poly:

Want your business to be the top-listed engineering company in Seaford?