Carpentry, Computers, and Solutions

Call Directions

Carpentry, Computers, and Solutions Here to make it happen, the way you want!
Where there's a Will, there's a Way!
A Degree in Computer Science and years of experience under my belt.

Put my knowledge to work for you!

Helping some friends with the container again! Got all the drywall up! Time for some mud!
2026-11-02

Helping some friends with the container again! Got all the drywall up! Time for some mud!

Stairs are looking pretty good 😎
2026-11-02

Stairs are looking pretty good 😎

Was helping some folks frame in a new extension on their house, got the plugs and smoke detector all wired up, insulatio...
2026-10-27

Was helping some folks frame in a new extension on their house, got the plugs and smoke detector all wired up, insulation packed away, and most of the v***r barrier done!

Started work on a landing for the front to go with that slab! 5'w x 5'3"L, Gonna sit at 24inches high, have 3 steps, 6 i...
2026-10-19

Started work on a landing for the front to go with that slab! 5'w x 5'3"L, Gonna sit at 24inches high, have 3 steps, 6 inch rise, 10.5 inch run. I'll use deck boards for the steps and stain it all with a wood sealer to give it all a uniform appearance!
Going to have a hand rail on one side sitting around 37.5", still debating where to put the steps, probably centered on the front door, once that's decided I'll make another hole for the post for the hand rail for the stairs. Using a 7/32 " shank as a spacer for all the boards and standard 4" (3-1/2") deck boards for the work

Progress! What do you think? It's looking pretty good now, but just wait till it's all closed in with that new window! G...
2026-10-04

Progress! What do you think? It's looking pretty good now, but just wait till it's all closed in with that new window! Gonna look amazing 😍

Well we're trying something new today! Getting that concrete poured, was looking at maybe just hiring a finisher, but I ...
2026-09-21

Well we're trying something new today! Getting that concrete poured, was looking at maybe just hiring a finisher, but I figured what better time to learn! Haha turned out pretty good! Some room for improvement, but not terrible for my first pour 😎
Powerfist to the rescue, got a little concrete tool set from princess auto.
Thanks to for their services and super helpful driver! Made the experience easier than I was expecting 🤩

Some winter prep! Now that the woodshed is vertical, it still has no roof, but that's a minor inconvenience, once all th...
2026-09-18

Some winter prep! Now that the woodshed is vertical, it still has no roof, but that's a minor inconvenience, once all the wood is cut I can load it up! And then keep moving with my million other projects

Sunday! Let's get some rebar bent and progress on the front slab! Got my 10mm rebar bent at 16" intervals, figured it wa...
2026-09-14

Sunday! Let's get some rebar bent and progress on the front slab! Got my 10mm rebar bent at 16" intervals, figured it was easier to bend it then cut off the metal and waste it? Now it'll add a bit of extra rigidity to the concrete exterior perimeter! I may have bent too many and should be able to double up along the exterior perimeter with a solid bar. I plan on having a wall resting there so the double layer of rebar along there is welcome! I may be over engineering it a bit, but better to have it last long 😎

Here's how that wood shed progressed this Saturday! Got everything all leveled off, platform in place, end walls up, sid...
2026-09-14

Here's how that wood shed progressed this Saturday! Got everything all leveled off, platform in place, end walls up, side walls up, everything screwed together... Next I guess are some trusses and a roof then we load it up with wood for the winter! Should hold almost 3 cords fully loaded I hope! 6' x 8'4" platform and 8' walls. More winter prep to come!

My first year here, I had attempted to make an oversized wood pallet with leftover wood, to use as a woodshed. A few wee...
2026-09-12

My first year here, I had attempted to make an oversized wood pallet with leftover wood, to use as a woodshed. A few weeks later added some makeshift ends to help hold the wood in, loaded two cords onto it, and then the wind came along and said "nah, you didn't brace that enough for me" and huffed and puffed and blew it over. The following year, I added some side walls to help brace the ends, and the result is what you see before you. Now this year, I've moved the back decks in preparation for leveling it out, cleared a new spot for the wood shed to go, added some rocks, leveled it out a bit as best as I could eyeball.

Next step is to grab 4 patio stones that I have leftover from the decks, find my high point on the square and throw a 2x6 between the patio stones for some finer leveling, I'll throw my level on it and add stones as needed till we're looking good. Then we can move the woodshed to its new location, add all the walls back on, and this year, well add a proper roof to protect all the birch wood we've been drying.
I've also upgraded the wood stove to a 3800sq ft unit with some blowers, J.A. Roby Ultimate 2015, nice wood stove for the year! Got new fire bricks for it, and slowly setting up my new ICC Ultra black pipes to go along with it.

Address

Rogersville, NB

Telephone

+5142504696

Website

Alerts

Be the first to know and let us send you an email when Carpentry, Computers, and Solutions posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Nearby engineering companies


Other Construction Companies in Rogersville

Show All