Advantis Engineering ApS

Advantis Engineering ApS Advantis Engineering er en ingeniør- og udviklingsvirksomhed. Vi leverer innovative løsninger

🌍 Composite recycling technologies🔍 Overview: Key Composite Recycling Technologies1. Mechanical Recycling👉Method: Shredd...
06/08/2025

🌍 Composite recycling technologies

🔍 Overview: Key Composite Recycling Technologies

1. Mechanical Recycling
👉Method: Shredding/grinding into smaller particles, then reused as filler in concrete, panels, or asphalt.
👉Pros: Low cost, scalable, relatively simple.
👉Cons: Material quality is degraded; limited to low-value applications.
👉Best for: Wind turbine blades, construction panels, low-grade reuse.

2. Thermal Recycling (Pyrolysis)
👉Method: High-temperature treatment in absence of oxygen to recover carbon or glass fibers.
👉Pros: Recovers valuable fibers with reasonable strength retention.
👉Cons: Energy-intensive; not ideal for glass fibers; emissions must be controlled.
👉Best for: Aerospace-grade carbon composites.

3. Chemical Recycling (Solvolysis)
👉Method: Use of solvents at controlled temperatures and pressure to dissolve the resin and free the fibers.
👉Pros: High-quality fiber recovery; potential for resin component reuse.
👉Cons: Expensive; complex; still in pilot stages.
👉Best for: High-end composites in aerospace and automotive.

4. Co-Processing in Cement Kilns
👉Method: Using composite waste as a fuel and material substitute in cement production.
👉Pros: Large-scale infrastructure exists; no ash left behind; reduces fossil fuel use.
👉Cons: No material recovery; not a true circular solution.
👉Best for: Fiberglass from wind blades and boats.

5. Reuse and Repurposing
👉Method: Mechanical cutting or modification to reuse large composite parts (e.g. in construction).
👉Pros: Low energy, low cost, keeps material in use.
👉Cons: Limited by design, logistics, and structural integrity.
👉Best for: Wind turbine blades, boat hulls.

At Advantis ApS, we believe reuse and mechanical pre-processing—especially on-site solutions like our Blade Cutter—offer one of the most immediate and scalable steps forward. They:
✅ Drastically reduce transportation and logistics challenges
✅ Enable local recycling partnerships
✅ Support modular or partial reuse of large composite structures
✅ Fit directly into broader circular economy strategies

🚦Advantis offers a 🔧 Blade Cutter – a powerful, mobile, and modular solution for cutting down wind turbine blades safely, efficiently, and with minimal environmental impact.

📩 Contact us today or visit https://lnkd.in/dzJtekmm for more info.

06/08/2025

🚀 Smarter. Safer. Sustainable.

At Advantis, we’re transforming how heavy industries work at height and move big things.

Our Modular Platform System (AMPS) and Heavy Lift Movers offer a scalable, reusable, and cost-efficient solution for hashtag , hashtag , hashtag and more.

🛠️ Faster configuration
💰 Lower cost
♻️ Smaller CO₂ footprint

Curious how it works in practice?
Read our latest article here 👇

08/07/2025

🌍 Invest in the Future of Wind Turbine Recycling

Introducing the Advantis Blade Cutter – Innovation with Impact
As the global wind industry faces a mounting challenge in end-of-life blade management and a growing logistical headache; Advantis offers a breakthrough:

🔧 The Blade Cutter – a powerful, mobile, and modular solution for cutting down wind turbine blades safely, efficiently, and with minimal environmental impact.
✅ Designed for on-site use (fits in a 40" container)
✅ Wet & dry cutting options with dust collection
✅ Proven results in collaboration with top industry players
✅ 99% material reuse potential – supports circular economy goals
✅ Strategic partnership for the whole value chain
✅ Proven results in cutting other materials e.g. steel, district heating pipes, subsea cables, etc.

💡 Now is the time to invest in scalable green technology. We're finalizing our first commercial Blade Cutter – ready after summer 2025 – and looking for strategic partners who share our vision for a more sustainable wind industry.

👉 Let’s talk about opportunities to invest, collaborate, or deploy the Blade Cutter in your operations.

📩 Contact us today or visit https://lnkd.in/dzJtekmm for more info.

🌍 How Wind is going Circular (Blade recycling)Wind turbine blades are made up of composite materials that boost the perf...
08/07/2025

🌍 How Wind is going Circular (Blade recycling)

Wind turbine blades are made up of composite materials that boost the performance of wind energy by allowing lighter and longer blades. Today 2.5 million tonnes of composite material are in use in the wind energy sector. ⚖️

The wind industry is committed to sustainable waste management 👌 in line with the multi-step approach put forward by the EU. In this approach waste prevention is regarded as the most favourable option followed by repurposing, recycling and disposal.

Wind turbines already have a recyclability rate of 85% to 90%. 👍 Most components of a wind turbine – the foundation, tower, components of the gear box and generator – are recyclable and are treated as such.

Wind turbine blades represent a specific challenge 🏗️ due to the complex nature of materials used to manufacture them. 15,000 wind turbine blades will be decommissioned in the next five years. Dealing with this significant volume requires logistical and technological solutions for the collection, transportation and waste management of the relevant material.

🚦Advantis offers a 🔧 Blade Cutter – a powerful, mobile, and modular solution for cutting down wind turbine blades safely, efficiently, and with minimal environmental impact

📩 Contact us today or visit https://lnkd.in/dzJtekmm for more info.

27/06/2025

Just a small video about our Blade Cutter "on tour" 👏 and a test we did for some 62m long blade. do you want more information please give us a call.

Yesterday we also tested cutting through, district heating pipes and submarine cables with big succes 💪

The next step is to complete the first commercial Blade Cutter, which is scheduled to be ready after the summer holidays, as we have already been working on all the necessary updates since this test. 👍

Yesterday we successfully completed the load test of the Hub Lifting Yoke with a load of 262 tons at the Liftra test cen...
27/06/2025

Yesterday we successfully completed the load test of the Hub Lifting Yoke with a load of 262 tons at the Liftra test center in Nakskov. 👏

WLL- 170 Tons
Load test - 262 Tons
FEA - 340 Tons

No issues or deformations were observed during or after the test. 💪 This is a fantastic achievement, thanks to our dedicated employees, smart design, and solid calculations, all approved by DNV. 🎉 Also a big thanks to Veerendra Sigireddy to handle this project with a steady hand. 👏 and Jonas Thorgaard for keeping the calculation on the right track 👏

Advantis ApS first lifting tool in that size. We appreciate our customer’s trust in us to manage this project with confidence and professionalism. 👍

Also thanks our supplier Ålsrode Smede & Maskinfabrik A/S

Next step FAT test and then surface treatment before delivering to our customer

Advantis ApS deltog sidste torsdag i AndersenB2B sommerafslutning hvor vi fra morgenstunden frem til frokost var på besø...
27/06/2025

Advantis ApS deltog sidste torsdag i AndersenB2B sommerafslutning hvor vi fra morgenstunden frem til frokost var på besøg ved ATN Service ApS i Skjern hvor Allan Trip Nielsen og Mogens Hansen fortalte om udenlands Arbejdskraft fra Polen 👏 og senere var Jakob Lemming på banen og fortælle om Digital Transformation Lab i Skjern der er en satelit af Aarhus University. Begge indlæg super spændende. 💪

Frokosten blev nydt ved Skjern golfklub 🚶 hvor vi fik gået 6 huller og de helt suverene vindere 💪 👏 af turnering blev. Kim Hansen fra VF Stålindustri, Bruno Engelbrektsen fra Automation, Frederik Kjærulff Jensen fra Profil Design Trading ApS og Kim D. Jensen fra Advantis ApS en helt igennem dejlig eftermiddag med sport og hygge. 👌

Der blev slutte af med en lækker middag på Restaurant Kalo i Ringkøbing hvor alle fik en "opgave" som Sanne Kjeldsteen havde forberedt udover at styre dagens event sikkert igennem, Tak til alle for en super god dag og vi ses efter sommerferien 🎉

Vi Advantis A/S havde fornøjelsen 🎉 af at deltage i Hosta Industries A/S inspirationsdag den 4 juni, i Hjallerup. En sup...
06/06/2025

Vi Advantis A/S havde fornøjelsen 🎉 af at deltage i Hosta Industries A/S inspirationsdag den 4 juni, i Hjallerup. En super god dag i godt selskab med masser af inspiration og netværk, tak til Christian Mosevang 👏 for invitationen og gæstfriheden og tillykke med jeres 2 nye rørlaser skærer det kan kun blive godt. Dagen sluttede med en times indlæg med Mr. Le Mans Tom Kristensen der fortalte om vigtigheden af Team samarbejde og dedikation, en ting vi alle kan tage med i hverdagen 👌

Hele dagen blev styret med hårdhånd af Sanne Kjeldsteen fra AndersenB2B

Vild med vilje !! Advantis ApS arbejder aktivt med diversitet også for andre end vores kunder og medarbejdere, nemlig in...
03/06/2025

Vild med vilje !!
Advantis ApS arbejder aktivt med diversitet også for andre end vores kunder og medarbejdere, nemlig insekter og andre smådyr, såldes vi kan forbedre forholdende for hele kloden.

Wild by purpose!!
Advantis ApS actively works with diversity—not only for our customers and employees but also for insects and other small creatures. In this way, we aim to improve conditions for the entire planet.

16/05/2025

Erhvervsambassadør Kim D. Jensen fra virksomheden Advantis A/S

Torsdag blev den årlige generalforsamling i Favrskov Erhverv afholdt ved Junget A/S og i den forbindelse blev Advantis A...
21/03/2025

Torsdag blev den årlige generalforsamling i Favrskov Erhverv afholdt ved Junget A/S og i den forbindelse blev Advantis ApS direktør Kim D. Jensen valgt ind i bestyrelse sammmen med formand Kent H. Jeppesen fra Foxway Group , og John Nielsen fra OnlineSynlighed.dk herudover består bestyrelsen af Tina Halkiær Olesen fra ApS l og Thorvald Horup fra Homatic Engineering A/S

Kim D. Jensen udtaler “jeg glæder mig til samarbejdet i bestyrelsen samt fremme erhvervs samarbejder i Favrskov med mit fokus på innovation, iværksætter miljøet i kommunen samt og ikke mindst samarbejdet virksomhederne imellem”

Adresse

Rho 8
Hinnerup
8382

Telefon

+4525297586

Internet side

Underretninger

Vær den første til at vide, og lad os sende dig en email, når Advantis Engineering ApS sender nyheder og tilbud. Din e-mail-adresse vil ikke blive brugt til andre formål, og du kan til enhver tid afmelde dig.

Genveje

Del

Type