MIDFIX

MIDFIX Midland Fixings Ltd, has over the past 40 years grown to become a leading and trusted supplier to the building services sector.

MIDFIX are experts in onsite and offsite supports for the mechanical and electrical industries, delivered through design, engineering, fabrication and industry training. Based in Nottingham in a 28000 ft. premises comprising of a warehouse, fabrication workshop, trade counter and offices, we specialise in a wide and diverse range of products and services that support pipework, electrical systems a

nd HVAC. Working with some of the largest mechanical and electrical companies in the UK, our mission is to make life easy for our customers. As specialists in our field and ISO 9001 accredited, we have heavily invested in stock to offer our customers an unrivalled package of expert advice, reliable service and support.

Torque matters in M&E installations.Is a calibrated torque wrench really necessary when installing M&E anchors and suppo...
04/09/2026

Torque matters in M&E installations.

Is a calibrated torque wrench really necessary when installing M&E anchors and supports?

In short, yes.

Torque is not simply about making a fixing “tight enough”.

It is about applying the specified force so the fixing can perform as intended.

Too much torque can damage a fixing.

Too little can leave a connection short of the required performance.

And when specified torque values are missed altogether, it can create uncertainty around the installation.

A calibrated torque wrench gives installers a clear, repeatable way to apply the correct torque.

That can help M&E installers follow the relevant installation guidance, reduce avoidable rework and provide clearer evidence of the work completed.

BS 8539 sets out guidance on the installation of post-installed anchors, including the importance of following specified torque values.

For projects where installation records are required, using a calibrated tool also makes torque application easier to demonstrate.

At MIDFIX, we see torque control as one of the practical details that helps support installations stay consistent from drawing to site.

How does your team verify torque on site?

M&E support systems are more than brackets and fixings.They are what hold containment, pipework and building services in...
03/09/2026

M&E support systems are more than brackets and fixings.

They are what hold containment, pipework and building services in place.

And the difference is not only in the individual components.

It is in how those components work together, how the system is installed and how that work is evidenced.

Problems can arise when parts from different sources are brought together without clear system data.

Or when a support is installed without the engineering information to verify the proposed load.

Or when the project team needs evidence later and it is not readily available.

Before installation, three questions can help bring clarity.

Is the support system supported by load data for the assembly, rather than just individual parts?

Are the installation instructions understood and followed on site?

And can the team identify the components and access the relevant test and training records when needed?

For MIDFIX, this is about making M&E support systems easier to specify, install and evidence.

Getting the system right gives design, installation and project teams more confidence in the work beneath the services.

How are you building that confidence into your support systems?

A support system isn't a system unless it's been tested as one. And an M&E support bracket is not proven by a folder ful...
02/09/2026

A support system isn't a system unless it's been tested as one.

And an M&E support bracket is not proven by a folder full of component data.

A channel section, anchor and channel nut can each have published technical information.

That does not automatically evidence the performance of the assembled support bracket.

The evidence needs to cover the actual configuration being specified: the components, their connections and the loading conditions they are intended to work under.

That is the difference between selecting compatible parts and being able to demonstrate a tested support system.

For M&E contractors, this matters well beyond the drawing stage.

Clear system evidence makes technical submittals easier to review, gives installers a defined configuration to follow, and leaves a more traceable record of what has been installed.

Where a tested and independently verified support system is required, component datasheets alone are not the whole answer.

The manufacturer’s system evidence should show what the assembled bracket has been assessed to do.

At MIDFIX, we help contractors look at support assemblies as complete systems, with the technical information needed to specify and install them with confidence.

Before installation starts, can the evidence show how the whole bracket performs—not only what each individual component can do?

01/09/2026

Bracket calculations don’t need to be a guessing game.

When an M&E support bracket carries containment, pipework or services across multiple tiers, the details matter.

Support spacing.

Service loads.

The substrate you are fixing into.

dynaMX® helps you bring those details together before installation.

Enter the bracket dimensions, add the services, select concrete or composite decking, then build and review the bracket in a 3D model.

You can rotate it, check the configuration and refine it before it reaches site.

The result is a drawing and calculation report that helps evidence how the bracket has been designed for the applied loads.

That gives the design and installation team something more useful than an assumption.

It gives them a clearer route from bracket layout to documented engineering information.

Whether you are working through a straightforward support or a more complex multi-tier arrangement, dynaMX® makes the design process quicker to review and easier to evidence.

Watch the video to see it in action, then explore dynaMX® via the link in the comments.

What part of bracket design tends to take the most time on your projects?

Fixings boards are most useful when they make the site decision clearer.On anchor work, the selection can be right on th...
25/08/2026

Fixings boards are most useful when they make the site decision clearer.

On anchor work, the selection can be right on the technical submission and still become difficult to evidence later if the information does not travel cleanly to the point of installation.

The practical link is simple:

- which fixing has been specified
- where it is being used
- which tool or method applies
- whether any change has been approved
- what record needs to be retained

For M&E contractors, that visibility helps supervisors and installers work from the same basis. It reduces the need to check from memory, guess from similar-looking fixings, or rely on a document that never reaches the people doing the work.

That is why fixing boards and fixing records sit naturally inside a stronger Anchor Fixings Strategy.

They are not there to make the file heavier.

They are there to connect selection, supply, installation, checking and retained evidence, so the finished anchor installation is easier to explain later.

A good fixing board does not replace training, supervision or correct installation method.

It gives supervisors and installers a clearer reference point before the fixing is loaded and before the record is needed.

With a tested channel system, the connection detail is part of the evidence.The evidence behind an M&E support system is...
24/08/2026

With a tested channel system, the connection detail is part of the evidence.

The evidence behind an M&E support system is not held by one length of channel in isolation. It depends on the system being selected, assembled and recorded in line with the basis that made the data useful in the first place.

That is why the small installation details matter: specified system components, correct fastener size and grade, channel nuts seated properly, final tightening to the stated torque, and records that show what was installed.

For M&E installers and supervisors, these are not separate admin tasks. They protect the link between the design basis and the support that ends up on site.

They also give project engineers a cleaner way to explain what was selected, installed and checked.

That is where the MX Tested Channel System has its value. It gives M&E contractors a tested and traceable support-system foundation, but that evidence still depends on the installed arrangement matching the intended system and method.

If a connection detail changes, treat it as a technical question before it becomes a site workaround.

Competence can fall out of date before the certificate does.An installer may have completed the right course.The supervi...
21/08/2026

Competence can fall out of date before the certificate does.

An installer may have completed the right course.

The supervisor may have the record.

The specified product may still be on the drawing.

The live job can still move.

Access tightens.

A different crew picks up the work.

The torque wrench or setting tool is not available.

The substrate or fixing position is not what was expected.

Programme pressure turns a defined method into "make it work today".

That is when competence stops being only a training record.

It becomes a delivery condition.

For M&E contractors, training still matters.

It gives installers and supervisors a shared method, clearer stop points and a record that learning took place.

MIDFIX Academy helps most when it strengthens that starting point.

The project still has to keep that method usable.

The right tool has to be there.

The supervision has to match the task.

And when the live condition breaks the planned method, someone has to stop the work and reopen the decision.

That is how training, supervisor checks and installation records stay connected to the live task.

Before work carries on under changed conditions, make sure the method being signed off is still the method the site can actually carry out.

On above-ground pipework, adjustment works best when it is planned into the support system from the start.Drawings, plin...
20/08/2026

On above-ground pipework, adjustment works best when it is planned into the support system from the start.

Drawings, plinth levels and pipe positions do not always land exactly as expected once the installation reaches site.

That does not make adjustment a problem in itself.

The problem is when adjustment becomes unmanaged rework: cutting, welding, sending supports away for modification, using temporary supports, or asking installers to make a detail work without a clear basis.

For contractors installing above-ground pipework, the useful planning check is simple: where movement is likely, which parts can be adjusted, and what still needs confirming before the support is loaded.

That is where modular pipe support systems can be useful in the right application.

QMEXX Pipe Supports are built for above-ground pipework where real site conditions may need a controlled, adjustable arrangement rather than a late fabrication issue.

The point is not that every pipe support should be modular.

It is that site change should be allowed for deliberately, so the final support remains buildable, explainable and fit for purpose.

Rooftop space can get tight when plant, its frame, pipework, cable tray and maintenance access all need room.That is nor...
19/08/2026

Rooftop space can get tight when plant, its frame, pipework, cable tray and maintenance access all need room.

That is normal as plant positions move, services are added and maintenance needs become clearer during design development.

The space left for a walkway or stepover can be quickly used up.

Plant support and maintenance access may be designed separately, but both still need space in the same part of the roof.

MIDFIX can review MX-R Roof Supports and MX-R Access as one roof arrangement, with room allowed for maintenance access.

That means maintenance access can be worked through alongside the plant frame while its position is still being defined, rather than revisited once space is tight.

On a busy roof, that can mean fewer later changes to the walkway or stepover as the roof plan settles.

A request for a fire-rated M&E support can arrive sounding like a product question.For a multi-service M&E trapeze brack...
18/08/2026

A request for a fire-rated M&E support can arrive sounding like a product question.

For a multi-service M&E trapeze bracket, it is often a design question first.

The stated fire condition changes what the proposed bracket must be assessed against.

A product label cannot answer that on its own.

For the assessment to address the actual bracket, its configuration, supported services, load, fixing method, substrate and stated fire condition need to describe the same M&E support application.

That distinction matters when a support package is already moving through design, procurement or a technical submittal.

It lets the M&E contractor and technical reviewer decide whether the proposed bracket needs an application-specific assessment, and what that assessment needs to address.

MIDFIX FRS Design and Evidence helps the M&E contractor and technical reviewer assess a defined M&E support application and describe the support arrangement, the assessment approach, relevant evidence and stated limits.

It does not replace the wider fire strategy or make a blanket claim for the cable tray, pipework or cable being supported.

It gives the M&E contractor a clearer way to progress the support requirement without asking a product name to carry an engineering answer.

Address

The Parrs, Lilac Grove
Nottingham
NG91PJ

Opening Hours

Monday 7am - 4pm
Tuesday 7am - 4pm
Wednesday 7am - 4pm
Thursday 7am - 4pm
Friday 7am - 4pm

Telephone

0115 922 1585

Website

Alerts

Be the first to know and let us send you an email when MIDFIX posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category