Waterguard Services Ltd

09/11/2026

Compliance is one thing. Handover-proof operation is another.

Series 7 provides event logs and audit data at the panel (useful for handover, investigation and optimisation), plus a backup battery for mains loss scenarios.

It’s designed for real commercial operation — not just a tick-box line in the spec.

Full article link below.
https://www.waterguard.co.uk/blog/breeam-leak-detection-systems-series-7/

06/11/2026

FAQ it’s Friday ✅
Water damage claims are rarely “minor” once they spread.

𝗤: 𝗪𝗵𝗮𝘁 𝗮𝗿𝗲 𝘁𝗵𝗲 𝗯𝗲𝗻𝗲𝗳𝗶𝘁𝘀 𝗼𝗳 𝗮 𝗪𝗮𝘁𝗲𝗿𝗴𝘂𝗮𝗿𝗱 𝗳𝗼𝗿 𝗶𝗻𝘀𝘂𝗿𝗲𝗿𝘀 𝗮𝗻𝗱 𝗿𝗶𝘀𝗸 𝘁𝗲𝗮𝗺𝘀?

A: Waterguard is built to reduce the impact of escape of water by supporting:
✅ Early leak detection in high-risk areas
✅ Rapid isolation (where configured) to help limit loss severity
✅ Zoned visibility so response teams can pinpoint the issue faster
✅ Alarm/BMS outputs to support clear escalation and building processes
✅ Reduced disruption for occupants and operations

Working on a risk-led project? Speak to our team about the right setup for your next scheme:
https://www.waterguard.co.uk/contact-us/

05/11/2026

Specifying commercial leak detection shouldn’t be guesswork. Here’s the quick cheat sheet:

• 1 incoming main → Series 7
• 2 feeds → S7 Dual
• ‘Water present’ zones (tape/cable/probes) → Puddle
• Wet areas / out-of-hours → PIR Water Isolation

Full comparison + application examples:
https://www.waterguard.co.uk/blog/commercial-leak-detection-systems-guide/

Commercial leak detection systems. A guide comparing Waterguard systems for specifiers & M&E contractors.

04/11/2026

The product matters.
Support matters too.

Waterguard support across the project lifecycle, including collaboration with designers, contractors and risk managers, plus training, commissioning and handovers through experienced engineers.

For teams specifying or installing Waterguard Puddle, that kind of support can make the difference between “installed” and “properly implemented.”

If you’re planning leak detection for a new build, refurbishment or operational building, start the conversation early.

🔗 https://bit.ly/4tSqZzA

03/11/2026

On site, practicality matters.

The Waterguard S7 Dual is designed to be simple to install and operate, available in 12V DC and 230V AC versions, and compatible with pulsed water meters using 1, 10 and 100 litres per pulse. It is also available across a broad range of pipe sizes, helping contractors and engineers configure the system around the real application rather than forcing the project into a narrow specification.

That kind of flexibility can make a real difference during design, installation and handover.

Learn more:
https://bit.ly/47Wykor

02/11/2026

Construction sites do not use water like finished buildings, which is why site protection needs to reflect that.

SiteGuard+ was developed through project trials and adapted from Waterguard’s original Series 7 system with features added specifically for the complex water usage patterns found on construction sites. It can be used on sites of any size and at any project phase, helping teams manage water more intelligently while supporting safer working conditions.

Learn more:
https://bit.ly/3QRF8Oz

30/10/2026

The best leak detection system is not just bought — it is properly planned, installed and handed over.

𝗤𝘂𝗲𝘀𝘁𝗶𝗼𝗻: Who should install a water leak detection system?

𝗔𝗻𝘀𝘄𝗲𝗿: Installation should be carried out by competent professionals who understand both the plumbing and electrical requirements of the system.

For best results, the installer needs to understand the water supply layout, valve location, meter positioning, cable routes, power supplies, BMS requirements and how the building will be used after handover.

Waterguard works with approved installation partners and project teams to help ensure systems are installed, commissioned and supported correctly.

https://bit.ly/4xVnKJA

Need installation support for your next project? Contact Waterguard and we’ll help you plan the right route from specification to handover.

29/10/2026

Unsure about CIREG compliance on your site?

The has introduced a new Joint Code of Practice for preventing and managing escape of water on construction sites. Developed by and the , and endorsed by the and the , this guide is intended to replace, the CIREG 5th Edition of Best Practice Guidance.

With this in mind we have updated our own Waterguard Procurement Guide including compliance notes for our active automatic flow monitoring shutoff devices required for all mid- and high-rise construction projects.

Read more and download today https://shorturl.at/qqB6E.

From ruining interiors through damage to equipment and furnishings, to spurring the growth of mould and even causing the collapse of entire structures – water leaks can result in significant construction delays and heavy expenses.

28/10/2026

High-footfall buildings need controls that protect without getting in the way.

In schools, leisure centres and public facilities, washrooms and changing rooms can see constant traffic — but they also spend long periods empty. PIR Water Isolation keeps water available when people are using the space, then isolates when it’s not in use, with a configurable delay to suit the building.

👉 Talk to us about a setup for your facility type: https://www.waterguard.co.uk/products/commercial/passive-infra-red-pir/

27/10/2026

The cost of a leak is not always just the visible damage.

At Waterguard, we often remind people to look beyond the headline wording in their policy. Some policies may cover the damage caused by a leak but not the work needed to find it, such as lifting floors, removing plasterboard or carrying out specialist surveys. In some cases, putting decorative finishes back afterwards may not be fully covered either. That is exactly why leak prevention makes sense. It helps reduce the chance of being left with costs and disruption you were not expecting.

Read the article here:
https://bit.ly/42lr4iO