EJOT GHANA

11/08/2026

Did you know that EJOT products were used in the construction of the Dubai Mall?

10/08/2026

The building's architecture is as impressive as its dimensions. The facade, with its projecting sliding shutters, is particularly striking, constructed as a ventilated rainscreen façade.
The fibre cement panels used are securely supported by our CROSSFIX® substructure.
Why CROSSFIX®?
👉 Versatile and flexible
👉 Designed for heavy loads and extreme conditions
👉 Compatible with a wide variety of cladding materials
📍 University of Dubrovnik Student Residence
📐 ATAR Arhitektura AT.AR. d.o.o.
📸 ©️ University of Dubrovnik

04/08/2026

EJOT® Concrete screw JC6-ST stainless steel A4

Applications
* For embedment in cracked and non-cracked concrete C20/25 – C50/60
* Permanently wet indoor use
* Outdoor use, including industrial and maritime environments

Properties
* Stainless steel A4 with hardened steel tip
* Countersunk head and T-drive
* ETA approved for cracked and non-cracked concrete C20/25 – C50/60
* Concrete screws are intended for through installations
* No predefined tightening torque
Benefits
* Requires only a small drill hole
* Allows small spacing and edge distances
* The screw is fully removable

Technical specifications
* Drive: T30
* Fireresistenz: R120
* Stainless steel

28/07/2026

Hard. Harder. JZ5. 🔩
Large spans, high-strength steel substructures, and the highest demands on fastening technology?
👉 The JZ5 is our strongest sealing screw for the toughest steel applications.
It has been specifically developed for the mechanical fastening of components to heavy-duty and high-strength steel substructures.
Its hardened carbon steel thread-forming zone ensures a high level of process reliability during thread forming—even in high-strength steels and thick material sections.
The remainder of the screw body, including the sealing washer, is made of weather-resistant A2 stainless steel. This makes the JZ5 ideal for exposed outdoor applications, reliably protecting the fastening point against moisture ingress.

23/07/2026

Sweeping curves, glass, and light – Roztyly Plaza in Prague is a true highlight of modern architecture.
The design by Aulík Fišer architekti appears almost weightless, yet it's backed by sophisticated technology. EJOT played a key role in bringing this vision to life behind the scenes. Our fastening solutions securely hold the impressive facade in place – invisible, yet essential.
Project highlights:
• Green roof terraces for a better work-life balance
• A spectacular atrium at the heart of the building
• State-of-the-art facade engineering
We love it when our solutions give big ideas a solid foundation!

20/07/2026

Outstanding Innovation: EJOT Wins the German Innovation Award 2026!
Precision workmanship and visually flawless, durable façade solutions – that’s what the EJOT LT-TD system stands for.
EJOT received the award in the category “Excellence in Business to Business – Building & Elements.” This innovative solution for fastening façade cladding in ventilated rainscreen façades (VHF) ensures constraint-free installation, flawless surfaces, and thermal decoupling of the façade panel from the substructure.
EJOT Product Manager Jens Dickel commented:
“This award confirms our commitment to developing innovative solutions for our customers’ challenges.”
A strong testament to innovation – Made in Germany.

16/07/2026

Globally connected. Successful together. ⚽🌎
When nations come together at the FIFA World Cup, team spirit, trust, and collaboration are on full display. At EJOT, we experience this every day. Because our success comes from people—not products or technologies alone.
People with diverse experiences, perspectives, and cultures. People who share their knowledge, take responsibility, and develop solutions together. Success begins with strong connections. Between people.
EJOT. Bringing it together.

13/07/2026

EJOT® self-drilling screw JT6-2/5-5.0 VARIO
Specification
Applications
* To form floating and fixed points on substructures of rainscreen facades
* Fastening pre-drilled stainless steel or aluminium wall brackets to aluminium support profiles
Properties
* A4 stainless steel with hardened drill point
* One screw for all part combinations
* Sliding washer E14, Ø 14 mm
* Buffer zone between the screw head and sliding disk prevents excessive clamp load of the joint
* Pre-assembled captive sliding washer
* Consistently low contact pressure prevents stick-slip phenomenon
* No stripping / destruction of the thread in component II resulting in high tensile loading capacity
* High tensile and transverse load transmission in component II due to fine pitch thread
* General building authorities test certificate (abP) as proof of usability according to DIN 18516-1 (also available as informal English translation)
* Case hardened drill point of the JT6 version for fastening in steel support profiles (not part of the abP)
* Wall brackets made of stainless steel and aluminium are part of the abP
* Buffer zone serves as visual set control
* Same assembly concept for floating and fixed points
Technical specifications
* Diameter: 5.0 mm
* Drilling capacity: 3.00 mm
* Drive: Hexagon A/F8
* Montagedrehzahl: 1500 1/min
* Gleitscheibe E14, Ø 14 mm

10/07/2026

08/07/2026

🏗️ Vyn Residential Project in Vega, Haninge – Stockholm
For the new 16-storey residential building featuring a Corten steel façade, JC6-D concrete screws in various lengths were used. They securely fasten the top-hat profiles through PIR insulation of varying thicknesses, forming the foundation for a durable and stable façade substructure.
One of the biggest challenges in this project was the wide range of insulation thicknesses, varying from 50 to 180 mm. Despite these differences, the JC6-D ensures precise and stable alignment of the top-hat profiles. To meet structural requirements, four screw lengths were used: 100 mm, 175 mm, 215 mm, and 255 mm.
In addition to the varying insulation thicknesses, the use of 1.5 mm thick Corten steel profiles in the façade substructure was another key factor in selecting the JC6-D concrete screw.
The JC6-D was specifically chosen to prevent corrosion between the steel profiles and the fastener, ensuring long-term compatibility and durability.
Corten steel façades require a particularly robust and reliable substructure. The JC6-D delivers high strength and excellent fastening stability — as also highlighted by the client:
"The screw demonstrated outstanding strength and fastening stability, ensuring robust and reliable installation of the top-hat profiles, even with varying insulation thicknesses."
Vyn is part of the sustainable urban development in Vega. The combination of high-quality façade materials and flexible fastening technology ensures a durable structure, in line with the requirements of the Svanen-certified building concept. 🌿