KEDAR Industries

18/07/2026

29/06/2026

We are Hiring

10/04/2026

Vibration Basics

*Type of Vibration Measurement

1) Relative Vibration Measurement: Shaft vibration measurement relative to machine body (Non-Contact type sensors will be used)

2)Absolute Vibration Measurement: Casing vibration is the measurement of the case motion relative to free space or absolute motion
(Contact type sensor will be used)

*Vibration can be Measured in Three Parameters
1)Displacement : When RPM is less than 600
2)Velocity : When RPM is > 600 and < 60000
3)Acceleration: When RPM is > 60000

for more Details,
📞7030944490
📧[email protected]
🌐www.kedarind.com

02/04/2026

On the auspicious occasion of Hanuman Jayanti, may strength, devotion, and success guide your journey.

Get in touch with us to power your next project.
📞 Call: 7030944490
🌐 Visit: www.kedarind.com
📧 Email: [email protected]

25/03/2026

WHAT IS CALIBRATION?

Calibration refers to the process of adjusting or measuring an instrument or system to ensure that it produces accurate and reliable results.
In other words, it involves comparing the readings or output of a device to a standard or known value to determine its accuracy and correct any discrepancies.

CALIBRATION IS REQUIRED FOR,

1)Protect from process failure

2)Increase reliability and consistency of process instrument

3)Achieve better process accuracy

4)Minimize the DRIFT of process instrument

5)Assure compliance and certification

6)Provide traceability from known standard

7)Ensure safety of the plant

8)Save money and increase productivity

9)Ensure quality & finish work on time

For More Details,
📞 7030944490
🌐 www.kedarind.com
📧 [email protected]

19/03/2026

गुढी पाडव्याच्या हार्दिक शुभेच्छा! 🌼
या मराठी नववर्षात तुमच्या आयुष्यात यश, समृद्धी आणि नवीन संधींची गुढी उभारली जावो.

तुमच्या व्यवसायाच्या प्रगतीसाठी विश्वासार्ह सोल्यूशन्स — Kedar Ultimate Solutions

अधिक माहितीसाठी आजच संपर्क करा.
📞 Call: 7030944490
🌐 Visit: www.kedarind.com
📧 Email: [email protected]

#गुढीपाडवा

18/03/2026

Something about RO
1. What's is the difference between UF membrane and 20-micron disc filter.
20-micron disc filter removes only large particles like sand/silt. UF removes fine turbidity, colloids, bacteria, and viruses. UF is much finer than a disc filter.
2. When RO membrane can handle lower molecular weight contaminants, why to install UF?
RO removes dissolved salts but is very sensitive to fouling. UF removes turbidity, colloids, and microbes that can foul RO, thereby protect RO and increase membrane life.
3. If cartage filters in RO choked, how it effect membrane in RO.
Choked cartridges cause pressure drop and low flow. If pressure is increased or cartridges are bypassed, fine particles reach RO, causing rapid fouling, higher DP, frequent CIP, and membrane damage.

18/03/2026

What is a Transmitter?

A Transmitter is a device that converts the signal produced by a sensor into a standard instrumentation signal representing a process variable being measured and controlled. These standard electrical signals are commonly 4 to 20 mA or 1 to 5 volts.
Transmitters are widely used throughout the process industries.

Why Transmitters are Required?

Signal Conversion: Converts raw sensor signals into standardized electrical signals.

Robust Signal Transmission: Enhances signal quality through signal conditioning, linearization, and isolation.

Cost & Design Optimization: Minimizes maintenance costs and simplifies engineering design.

Eliminates the need for long, specialized sensor cables.

Allows for the use of standard 4-20mA I/P Cards at the DAQ/DCS level.

Signal Protection: Provides protection against Electromagnetic (EM) and Radio Frequency (RF) interference.

Noise Suppression: Suppresses unwanted noise through the use of digital filter
For more details,
📞 7030944490
🌐 www.kedarind.com
📧 [email protected]