MJM Machining

MJM Machining MJM Machining
Established 2024

Specialising in fi****ms repair, alterations and general gunsmithing. Contact Mike Maulder for enquires. 0277403586

This is the second re*****on 700 short action that we tidied up last month , the bolt handle was missing , so we silver ...
31/08/2026

This is the second re*****on 700 short action that we tidied up last month , the bolt handle was missing , so we silver soldered a new one on before we could fit the barrel. Fitting it into the stock we found the action screw holes in the stock didn't line up perfectly with the action itself , so into the milling machine to relieve the alloy bedding block to allow the recoil lug to sit further back ,success!

338 lapua time ! Will keep you guys posted .
29/08/2026

338 lapua time ! Will keep you guys posted .

Here's a job we did a while ago , we had to make a spacer to go between a Scope and thermal adaptor , as the original ...
27/08/2026

Here's a job we did a while ago , we had to make a spacer to go between a Scope and thermal adaptor , as the original one wasn't a good fit and the scope didnt hold zero on the target. We started by measuring the internals of the adaptor and found it not to be completely round , so we machined the bushing down to be a snug fit on the OD ,and slowly tapered the inside to suit the OD of the scope. We cut the bushing in half and assembled it. With everything being a snug fit the scope started to hold zero .

Went to do some work on this rifle and wondered why I couldn't undo the action screws. Another example of why you need t...
24/08/2026

Went to do some work on this rifle and wondered why I couldn't undo the action screws. Another example of why you need to do preventative maintenance on your fi****ms.

Managed to get another one finished this week , a Sako 85 222 for a new barrel . A quick borescope revealed quite a bit ...
22/08/2026

Managed to get another one finished this week , a Sako 85 222 for a new barrel . A quick borescope revealed quite a bit of rust and pitting . We inspected the action and checked the action face to the locking lugs with a micrometer and it looked in good shape , all three locking lugs on the bolt were contacting inside the action so onto fitting the new Truflite 1-9 twist barrel . Just need to head to the range and see how it shoots .

New reamer day , 6.5 and 22 creedmoor!
19/08/2026

New reamer day , 6.5 and 22 creedmoor!

Trigger job this week , a nice anschultz 22 which had some pieces missing from the trigger, unfortunately being an older...
18/08/2026

Trigger job this week , a nice anschultz 22 which had some pieces missing from the trigger, unfortunately being an older rifle there is nothing available on the shelf locally , so we had to make up a threaded sleeve and locking nut for the sear adjustment so we could make it operational.

Another thread job done , this time on a new single shot bergara , we quickly made up some bushings so we didnt mark the...
11/08/2026

Another thread job done , this time on a new single shot bergara , we quickly made up some bushings so we didnt mark the cerekote finish . This one also had a 1/2 to 5/8 adaptor for different muzzle device s .

Barrel fitting a chambering , this one is a 308win , there is a bit of time checking and double checking that everything...
10/08/2026

Barrel fitting a chambering , this one is a 308win , there is a bit of time checking and double checking that everything fits properly , the threads dont bind and there is clearance where is should be . A bit of time to polish things to make it tidy , shiny stuff shoots better or so im told . đŸ˜†

Action time !! Have two Re*****on short actions builds on the go at the moment, we gave them the once over before maki...
07/08/2026

Action time !! Have two Re*****on short actions builds on the go at the moment, we gave them the once over before making two many decisions . The recoil lugs on one of the actions were a bit worse for wear with some deep gauling marks in them , so we decided to clean them up , this worked out ok as one of the bolts provided had no handle which will need timing etc anyhow.A quick tidy up for the other action on the critical faces and a light lap of the bolt lugs and we're good to go to start taking measurements for barrel fitting .

Address

Levin
5571

Website

Alerts

Be the first to know and let us send you an email when MJM Machining posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category