Ubertas Industrial Trading

Directions Website

Ubertas Industrial Trading Your operations deserve materials you can count on. And that's exactly what we're here for. At Ubertas, we're more than a supplier.

We're a local partner committed to keeping your projects running smoothly. Ubertas Industrial Trading is a trusted seller of various industrial products ranging from welding supplies to safety goods for over a decade. Customers include local factories within Laguna that produce automotive and metal products who have come to trust our quality and service.

The A15 mounted points are small grinding tools on a 6 mm steel shank that fits into a die grinder or straight hand grin...
22/10/2026

The A15 mounted points are small grinding tools on a 6 mm steel shank that fits into a die grinder or straight hand grinder. The slim, pointed head reaches into tight corners, slots, and holes, which makes them handy for deburring, cleaning up welds, and smoothing castings on steel and most other metals. ⚙️

The marking on the pack, 40A+80Q8V, tells you more than it looks like:

• The A means aluminum oxide, a general-purpose abrasive for steel. The 40 and 80 are grit numbers, which point to removing material and smoothing rather than polishing.

•The Q is a hard grade, so the grains are held tightly and a small tip like this lasts longer.

• The 8 means an open structure with room for chips to clear, and the V is a vitrified, glass-like bond.

Each pack has 15 pieces. Message us for pricing, and confirm the maximum safe speed for your grinder before use. 📩

Joining thick steel isn’t one big zap. It’s layers. ⚡A welder runs a line of melted metal along the groove between two p...
21/10/2026

Joining thick steel isn’t one big zap. It’s layers. ⚡

A welder runs a line of melted metal along the groove between two pipes, then another on top, and another, until the groove is full. Each trip along the joint is called a pass. 👨‍🏭

On the Trans-Alaska Pipeline, the thicker pipe needed seven passes for each weld made on site, and the thinner pipe (11.7 millimeters) needed six. That thicker wall was about as thick as an AA battery is wide. With 66,000 welds made on site along a pipeline of about 1,300 kilometers (farther than Manila to Davao), that’s roughly 400,000 layers by our math. 😱

Before the first layer, crews warmed the pipe ends with propane torches to about 65 to 120 degrees Celsius. 🔥

Behind every strong joint are welding rods or wire, safety gear and clean, ground surfaces. That’s what we supply at Ubertas: welding materials, protective gear, and grinding and cutting discs. ⚙️

What’s the most impressive steel structure you’ve seen in person? Tell us below.

Sources:
https://alyeska-pipe.com/pipeline_facts/taps-construction/
https://www.gao.gov/products/EMD-77-44
https://alaska.libraryhost.com/repositories/2/top_containers/182

Plasma torches, electrodes, nozzles and more, available at Ubertas. 📣Worn consumables are often the reason for rough edg...
20/10/2026

Plasma torches, electrodes, nozzles and more, available at Ubertas. 📣

Worn consumables are often the reason for rough edges, slanted cuts and extra dross. Keep spares ready so your cutting line doesn’t wait on a part. 👇

Message us your torch model and quantity for a quotation. 📩

Happy Monday, everyone! 👋Most of a good casting is decided before the metal ever moves. The pattern is made, the mold is...
19/10/2026

Happy Monday, everyone! 👋

Most of a good casting is decided before the metal ever moves. The pattern is made, the mold is packed, the temperature is checked. The pour may only take moments, but the preparation behind it is what makes it count. 🦾

Your week works the same way. Do the groundwork today, then keep feeding the work, one task and one day at a time. It may not look like much halfway through. It will hold when it counts. 🙏

“In all labour there is profit.” Proverbs 14:23 🕊️

What are you feeding this week? Tell us in the comments. Have a strong one from all of us at Ubertas. 😊

Small part, big responsibility! ⚡ Ever wondered what makes a plasma electrode tick?It's all about putting the right meta...
16/10/2026

Small part, big responsibility! ⚡ Ever wondered what makes a plasma electrode tick?

It's all about putting the right metals to work. Copper does the heavy lifting by carrying electrical current and helping draw heat away from the electrode. Think of it as the hardworking backbone that keeps things running. ⚙️

Then there's hafnium, a lesser-known metal with a pretty important job. Found at the electrode's tip, it provides the point where the plasma arc forms, standing up to the extreme temperatures involved in cutting metal. Together, copper and hafnium make a practical team: one handles the current and heat, while the other takes on the arc. 🧑‍🏭

Even the smallest consumables have some clever engineering behind them! At Ubertas Industrial Trading, we supply genuine industrial consumables to help keep your operations running. Need plasma-cutting electrodes or other replacement parts? Send us a message for product inquiries, pricing, and availability! 💬

Sources:
https://www.hypertherm.com/resources/system-support/maintenance-and-use/consumable-care-and-optimization/extending-parts-and-consumables-life/
https://xnet.hypertherm.com/Xnet/library/library.jsp?file=HYP116271
https://esab.com/au/apc_en/products-solutions/product/manual-plasma-cutting/esab-cutmaster-100/

New plasma consumables out for delivery today to one of our customers 📦These include:📌 Cutting tip📌 Electrode📌 Cartridge...
15/10/2026

New plasma consumables out for delivery today to one of our customers 📦

These include:

📌 Cutting tip
📌 Electrode
📌 Cartridge
📌Shield cup

Message us for pricing and availability 📫

Three of the five parts in this view, the contact tip, diffuser, and nozzle, are front-end consumables, the pieces close...
14/10/2026

Three of the five parts in this view, the contact tip, diffuser, and nozzle, are front-end consumables, the pieces closest to the arc that are built to be replaced. Torch maker Bernard and Tregaskiss notes that nearly all of a MIG gun’s running cost and most of its downtime concentrate in that front end. 🧑‍🏭

Your weld usually tells you which part is struggling first. Lincoln Electric’s troubleshooting guide traces turbulent shielding gas, a leading cause of porosity, to spatter packed inside the nozzle or built up in the diffuser, and says a contact tip that has worn egg-shaped needs replacing. 🗒️

One tip before you reorder: names and fit vary by torch. Some guides call the diffuser a tip holder, and consumables are not universal, so match every part to your gun first. 🔎

Send us your torch model and we’ll help you match the right parts. Message us for pricing and availability. ✉️

Sources:
https://www.bernardtregaskiss.com/anatomy-of-a-mig-gun/
https://www.lincolnelectric.com/en/welding-and-cutting-resource-center/process-and-theory/mig-problems-and-remedies
https://weldingmart.com/collections/mig-consumables

From MIG torches and swan necks to contact tips, nozzles, cables, connectors, clamps, and electrode holders, we carry th...
13/10/2026

From MIG torches and swan necks to contact tips, nozzles, cables, connectors, clamps, and electrode holders, we carry the welding accessories and consumables to keep your setup running. 👨‍🏭

Message us for pricing and availability. 📩

Most weeks, the progress isn’t something you can see. It’s a pallet moved, a joint welded, a coat of paint on something ...
12/10/2026

Most weeks, the progress isn’t something you can see. It’s a pallet moved, a joint welded, a coat of paint on something still unfinished. But enough of those shifts, from enough hands, and something real gets built. It’s been a heavy season for a lot of us, and that’s okay to say out loud. 🙏

Keep showing up for the work and for each other, because nobody builds this alone. Here’s to a steady week ahead. 🌻

The branch is artistic license, but the wood pulp is real. In a cellulosic rod, a steel wire stays at the center and the...
09/10/2026

The branch is artistic license, but the wood pulp is real. In a cellulosic rod, a steel wire stays at the center and the plant fiber sits in the coating around it, bound together with salts and minerals. The catch is hydrogen, which raises the risk of cracking. That is the opposite of what low-hydrogen rods like the E7018 we decoded earlier this week are built for, so these rods are used selectively. 🌳

That same hydrogen is also what gives the arc its digging, driving push, which is why welders reach for these rods on pipe root passes, farm equipment repairs, and other jobs with dirty or contaminated surfaces. 👨‍🏭

The burn also leaves a weld pool that freezes quickly. Every rod trades pe*******on, strength, and cracking resistance differently, so the right one depends on the job. ✅

Message us and we'll help you find the right welding electrode for yours. 📩

Address

3 Golden Farm Phase 2 Pacita 2
San Pedro
4023

Opening Hours

Monday 9am - 5pm
Tuesday 9am - 5pm
Wednesday 9am - 5pm
Thursday 9am - 5pm
Friday 9am - 5pm
Saturday 8am - 5pm

Website

Alerts

Be the first to know and let us send you an email when Ubertas Industrial Trading posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category