Crazydayz Fab

09/01/2026

Support small businesses!! 🙏

Metal products designed and built by Crazydayz Fab

08/31/2026

Next up was this 2006 Single cab Silverado in for a 3/6 drop.

Front was a coilover kit.

Rear was a flip kit, that needed a saddle made.

Got the front stock parts tore down and installed the new parts.

I used my plasma table to cut the pieces for the saddle.

Then used my welder to weld em up.

Pulled the bed and stock hardware holding the axle housing to the leaf springs.

Flipped the axle housing to the top of the leaf springs and bolted its all back together.

Slapped the bed on and bam!! Long bed slammed.

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

******Link in the bio******

08/26/2026

7 years ago…. Times have changed.
Built the chopped S10 and the blue Silverado under a carport 🤯

08/24/2026

Gave Victor Cano a hand with some welding.

He is currently in the middle of his bodydrop.

While cycling the suspension he realized he needed to do a front kit as his factory arms wouldn’t cut it anymore.

He needed his spindles drilled and reverse reamed.

After knocking that out we went to his place for me to weld up the front kit from Nfamus Metal Fab.

This kit is pretty straightforward to install.

He had the front end cut, cleaned up before I showed up.

Tacked em up, then welded it all up.

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/73FxbvlLBcc?is=rRTPbCy8CDRaX0SH

08/19/2026

https://crazydayzfab.myshopify.com/

Metal products designed and built by Crazydayz Fab

08/19/2026

https://youtu.be/ouoWOQ0LnXk?is=Iuh1Bj3zJbSIvWju

In this episode:I finish the installation after having to redo pa...

08/17/2026

Front is all back together! 👏 🤯

So much have to be reconfigured 😱

I should have NOT welded the bag mounts in assuming they would work 🤦‍♂️

After checking the math (numbers don’t lie) I had to cut the upper bag mounts out. 😩

Designed some upper mounts that made the bag happy when layed out. 😉

The upper bag mounts that came with the kit, was at a bad angle and only had 2” on one side of the bracket when mocked up layed out…….

Since the bag mounts were figured out, I moved onto the shocks. 🤔

The lower tabs…. anywhere on the lower control arm would hit the inside of the wheel 🛞

Made some new lower tabs and modified the lower control arms…

The upper tabs would not work as well so they got cut off..

I made some new ones with perfect fitment the allowed perfect clearance between the wheel and air bags.

Trimmed the inner tie rods to compensate for the arms being narrowed.

Got everything put together and temporally have the front bags ran to a tee until I figure out air management placement later down the build.

I need to mount the factory brake line bracket to the upper control arms.

I also need to modify the tie rod adjuster to do a alignment.

As I always say, watch the YouTube videos!
I don’t take as many pics as I do videos 😉🫣

Go check it out!
Subscribe if you aren’t already 🙏

https://youtu.be/ouoWOQ0LnXk?is=sFkhp8ND5MQpHHGK

https://crazydayzfab.myshopify.com/

08/12/2026

https://youtu.be/F1JhjoK-VFc?is=I7gq51H1mZGAnuYd

In this episode:I tear down the front suspension on my 2016 Silve...