Positive Pulse

Positive Pulse Spreading positivity, peace, and good energy every single day.

A raise can increase your wealth or simply increase your spending. 💰Before upgrading your lifestyle, decide how much of ...
09/02/2026

A raise can increase your wealth or simply increase your spending. 💰

Before upgrading your lifestyle, decide how much of every raise will go toward your future.

More income only helps when some of it stays with you.

You just got an extra $1,000 every month.

How much are you saving or investing? 👇

A bigger salary can create a bigger lifestyle instead of bigger wealth. 💰The real question isn't only:“How much do you e...
09/02/2026

A bigger salary can create a bigger lifestyle instead of bigger wealth. 💰

The real question isn't only:

“How much do you earn?”

It's:

“How much do you keep, invest and grow?”

Which matters more to you: higher income or a higher savings rate? 👇

The center pivot bracket on an old steel seesaw had developed play, making the board rock unevenly from side to side. I ...
08/30/2026

The center pivot bracket on an old steel seesaw had developed play, making the board rock unevenly from side to side. I removed the worn pivot supports and fabricated new side plates from 1/4 inch steel. I welded the plates to a reinforced center frame, added two triangular gussets and installed a new pivot sleeve through the middle. Before finishing the assembly, I checked that the seesaw moved smoothly without binding. Once everything was aligned, I completed the welds and tested the movement several times. The pivot now feels tight and the board moves evenly from both sides. The final welds were left unpainted and fully visible.

A section of steel handrail on an old rollercoaster maintenance platform had developed a cracked mounting joint. The rai...
08/30/2026

A section of steel handrail on an old rollercoaster maintenance platform had developed a cracked mounting joint. The rail was still standing, but I didn't like the amount of movement in it. I removed the damaged bracket and fabricated a new mounting plate from 3/8 inch steel. I fitted the plate to the existing platform frame, added a triangular gusset beneath the rail connection and welded the joint with multiple passes. After the weld cooled, I checked the rail from several directions and verified that the repaired section stayed rigid. The final welds were left unpainted and fully visible for inspection.

A go-around is a normal and important aviation safety procedure. ✈️Instead of forcing a landing when the approach is uns...
08/24/2026

A go-around is a normal and important aviation safety procedure. ✈️

Instead of forcing a landing when the approach is unstable or conditions are unsuitable, pilots apply takeoff or go-around power and climb away before preparing for another approach.

The Boeing 787 uses high-bypass turbofan engines designed for efficient long-haul flight. ✈️A large fan moves a signific...
08/24/2026

The Boeing 787 uses high-bypass turbofan engines designed for efficient long-haul flight. ✈️

A large fan moves a significant volume of air around the engine core, helping produce thrust efficiently while also contributing to lower noise compared with older engine designs.

08/22/2026

My outdoor trash cans kept blowing over whenever a strong storm came through. I got tired of picking up garbage across the yard, so I built a steel holder around them. I welded a rectangular frame from 1 inch square tubing, added upright corner posts, and welded two short front rails to keep the cans from rolling forward. I added a rear crossbar for strength and anchor tabs at the bottom so I could bolt the frame to a concrete pad. The cans can still be rolled in and out easily, but wind can't knock them over anymore. The final welds were left unpainted and fully visible.

08/22/2026

My kayak was leaning against the side of the garage and falling over every time I moved something nearby. I decided to build a proper wall rack from steel. I welded two mounting frames from 1 inch square tubing, added curved support arms from round bar, and connected the arms with short cross braces for strength. I welded flat mounting plates onto the back and bolted the whole rack securely to the wall studs. The kayak now rests safely off the floor and stays completely out of the way. No more leaning it against the wall and hoping it doesn't fall. The final welds were left unpainted and fully visible.

The battery cover on my excavator had cracked around the hinge and kept vibrating against the body panel. I removed the ...
08/21/2026

The battery cover on my excavator had cracked around the hinge and kept vibrating against the body panel. I removed the damaged hinge section, fabricated a new 1/4 inch steel bracket, and welded it to the frame with four passes. I installed a new hinge pin and added a small gusset underneath the bracket. The cover opens smoothly now and stays tight when the machine is running. The final welds were left unpainted and fully visible.

One leg on my old steel shop stool had cracked at the lower joint and the stool rocked whenever I sat on it. I cut away ...
08/21/2026

One leg on my old steel shop stool had cracked at the lower joint and the stool rocked whenever I sat on it. I cut away the damaged section, fabricated a new foot from 1 inch square tubing, and welded it to the frame with four passes. I added a small triangular gusset at the joint and leveled the stool before the weld cooled. It sits solid now without rocking across the concrete floor. The final welds were left unpainted and fully visible.

Address

Los Angeles, CA

Website

Alerts

Be the first to know and let us send you an email when Positive Pulse posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Positive Pulse:

Shortcuts

Share