Mike's Cylinder Heads

Call Directions

Mike's Cylinder Heads Mike's Cylinder heads specializes in automotive, industrial, marine Cylinder head reconditioning

10/29/2026

Final pass resurfacing a BMW cylinder head. All good to go back into service.

Next up is a 425 Oldsmobile.
10/26/2026

Next up is a 425 Oldsmobile.

Big block Ford 521ci stroker build. Edelbrock heads and custom roller cam from powell cams. This will be getting a blowe...
10/20/2026

Big block Ford 521ci stroker build.
Edelbrock heads and custom roller cam from powell cams. This will be getting a blower and going into replica Ford Falcon Mad Max movie car..

10/15/2026

Can't say it better myself. Get this multiple times a week.

Spent the day correcting problems on these new out the box  heads that sell for just over $3000 for a engine build I'm d...
10/14/2026

Spent the day correcting problems on these new out the box heads that sell for just over $3000 for a engine build I'm doing. With my experience I did expect some issues on these.

First thing I did was remove springs and check installed heights of the springs and spring pressures. 15 were at 1.950" which is spec 1 had an extra .015" shim and installed at 1.935".

Next I vacuum checked valves to see how good the valves seal. Most would only pull 15" of vacuum. I like to see a minimum of 20". If perfect will pull and hold 25".

I then completely disassembled them and noticed how dirty the heads were. The bronze guides had been machined and not cleaned before assembly. Bronze grit mixed with assembly l**e to form a fine abrasive paste to run in the new guides. You can see it on the paper towel and on the spring shims in the pics. This would have rapidly worn the guides out or even possibly stuck a valve.

After cleaning the guides I wanted to see how bad the seats were. I applied ink to seats and lightly lapped a couple valves to see what was going on. As you can see it's not making full contact around the seat and why they wouldn't pull good vacuum.

I then checked guide clearance and found were on the tight side for my liking. I honed them to my desired sizes and put on machine to recut all the seats and resurfaced the decks to make sure they were perfect.

A lot of time and money into these for the money that was spent on them and are advertised as "bolt on and go". I find this to be typical of parts now a days. I found out long ago new means needs extra work. Never trust anything is good out of the box.

10/03/2026

A pair of Ford coyote heads brought in to chase an oil consumption issue. I found an aftermarket spring setup installed with a positive seal that was loose fitting on the guide causing multiple seals to ride off the guide letting oil in. I installed the correct seals shown in comments on the left and the customer will be good to go now.

10/02/2026

Pressure testing a Ford 2.3 turbo cylinder head from a mustang. Shown is a crack in the exhaust port just like the 1.5 I posted the other day. What's really crazy is just like the 1.5 this one was also resurfaced and reinstalled. My guess is it's the same shop in town as they both were resurfaced on a belt sander type machine which just doesn't work either.
When shopping around for a machine shop ask what techniques and equipment are used. I've yet to have anyone ask me that in all the years I've been in business. If they are charging 1990s prices they are probably not equipped to properly repair your late model cylinder heads. You get what you pay for.

09/30/2026

This head was taken to another shop without capabilities to pressure test for cracks and was only resurfaced and installed back onto vehicle only to be removed and brought to me after still having the same problems. Quite a large crack that can only be found with a pressure test.

09/27/2026

It has been extremely busy the last few months and time for me to take some time off.
The next few weeks will be business as usual. Starting Oct 19th until mid December hours will be by appt.
Call or text if anything is needed. Please leave voicemail if I don't answer.
During this time my core focus will be doing heads for repair shops and daily driver type heads. Any performance, hotrod or restoration type work Ill get to it when I get to it.
If I've spoken with you about doing an engine build get with me asap to get it in the shop and in line as I'm just about booked up for the winter on builds.
Thanks
Mike

401 Buick nailhead rebuild complete. Just a stock rebuild with a TA performance intake manifold.
05/27/2026

401 Buick nailhead rebuild complete. Just a stock rebuild with a TA performance intake manifold.

Address

145 Malow Ste. B
Mount Clemens, MI
48043

Telephone

(586) 354-8502

Website

Alerts

Be the first to know and let us send you an email when Mike's Cylinder Heads posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category

Nearby engineering companies