McCrea Heavy Machine Works

McCrea Heavy Machine Works We are a full service metal shop. Offering machining, fabricating, welding, scrap metal demolition and removal.

Lift arms to raise and lower the flood gates for the Chesapeake & Ohio canal that's being restored by the national park ...
08/31/2026

Lift arms to raise and lower the flood gates for the Chesapeake & Ohio canal that's being restored by the national park service. 24' of 2 1/2"-4 acme thread and matching nuts all made by hand on manual machines.

Making some 8' long shafts with 6' of 2 1/2"-4 acme thread on the 18 foot lathe. Have to thread it in halves with the st...
08/05/2026

Making some 8' long shafts with 6' of 2 1/2"-4 acme thread on the 18 foot lathe. Have to thread it in halves with the steady rest because it's so long.

Set of shim plates to repair a large gantry crane that needed to be up and running asap. 2 18"×18", 2 18"×30" all milled...
07/20/2026

Set of shim plates to repair a large gantry crane that needed to be up and running asap. 2 18"×18", 2 18"×30" all milled to slightly different angles.

100 gallon fuel transfer tank that needed some leaks fixed and shortened from 54" to 49". Cut, welded, pressure tested, ...
07/01/2026

100 gallon fuel transfer tank that needed some leaks fixed and shortened from 54" to 49". Cut, welded, pressure tested, lifting lug and feet moved and rewelded then painted.

Wheel hub repair for a piece of heavy equipment. Bearing failed and wore the housing down 3/4" on one side. Machined dow...
06/28/2026

Wheel hub repair for a piece of heavy equipment. Bearing failed and wore the housing down 3/4" on one side. Machined down the hub till it was parallel, made a steel ring, preheated and carefully welded to join cast iron to steel then machined to original dimensions.

1.5" stainless steel tube knurled to be used as handrails at a spa.
05/19/2026

1.5" stainless steel tube knurled to be used as handrails at a spa.

1929 brass honeycomb radiator. It doesn't have any damage but I've never done a pressure test on it. Came from a hudson ...
05/13/2026

1929 brass honeycomb radiator. It doesn't have any damage but I've never done a pressure test on it. Came from a hudson with a super six engine. I can take any measurements needed to see if it fits your needs. $350 located in robesonia pa 19551

1929 transmission, bell housing, clutch, pressure plate and fly wheel. Came from a 29 hudson and will bolt to a super 6 ...
05/13/2026

1929 transmission, bell housing, clutch, pressure plate and fly wheel. Came from a 29 hudson and will bolt to a super 6 engine but can be changed with other bell housings. Has the original clutch with replaceable cork plugs. Has a box of random brackets and clutch pedal. $300 located in robesonia pa 19551

Torque roll i repaired on site for a customer. The shaft walked out 3.5" over time and needed pressed back in. (With my ...
04/19/2026

Torque roll i repaired on site for a customer. The shaft walked out 3.5" over time and needed pressed back in. (With my own handy press fixture i built just for these parts) I had to air arc out all the cracked welds and put a weld bevel on the id of both hubs so it could be permanently welded in place then ground flush so the bushings can be installed.

Drilling out the rusted in stub shaft of a 50" gear
04/15/2026

Drilling out the rusted in stub shaft of a 50" gear

Address

Robesonia, PA

Telephone

6106036442

Website

Alerts

Be the first to know and let us send you an email when McCrea Heavy Machine Works posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to McCrea Heavy Machine Works:

Shortcuts

Share

Category