Shaun Hight Construction

Shaun Hight Construction Ca license #1049864
Local craftsman specializing in custom homes & remodels in San Diego, CA.

1x6 redwood installed inside these gate frames fabricated by 👍👌
08/30/2019

1x6 redwood installed inside these gate frames fabricated by 👍👌

Inside or outside, doesn’t matter to me 👍👌
08/13/2019

Inside or outside, doesn’t matter to me 👍👌

06/06/2019

Had some fun learning/experimenting with the “burn finish”. It’s crazy what a torch and some linseed oil will do to a piece of timber. Burning these 4x10 rafters that I set 4ft OC that sit on 4x12 beam lines. The beams were mounted to true 1/4 round redwood tree logs that had 1/4” plate 3x3 L brackets mounted with 4” galvanized lag bolts and also two sets of 5/8” galvanized all thread through bolts that went through both the logs and the beam lines. Made for a nice strong setup and clean finish

Cal fill on this front entry I finished up. 9/12 pitch that dies on a 5/12 trussed roof. Hip/valley framing is fun to me...
04/28/2019

Cal fill on this front entry I finished up. 9/12 pitch that dies on a 5/12 trussed roof. Hip/valley framing is fun to me because of the compound miters and degrees involved in getting a clean finished product. There was no detail for the fill at the ridge so i added a choker with two 3” ledger locks at each end and a hanger for end support on the ridge instead of a post. Worked out nice 👌

Pretty well done with the framing portion of this addition for ... a few minor details on the interior and that’s a wra...
04/15/2019

Pretty well done with the framing portion of this addition for ... a few minor details on the interior and that’s a wrap 👍👍👍

04/03/2019

Some roof framing for this fine sunny Wednesday 👍👍👌👌

Something simple yet satisfying... glue your miters, hone out your 45’s a 1/16-1/8 inch, and A35 the inside to keep the ...
02/09/2019

Something simple yet satisfying... glue your miters, hone out your 45’s a 1/16-1/8 inch, and A35 the inside to keep the joints from spreading... long term, your facia will stay together longer and have a better finished result

11/28/2018

Jean shorts. Vans. One glove. 100 degree weather... 😂😂😂 ...I’ll still get the job done 👊🏼👊🏼👊🏼
Cutting some steel plates from old Vietnam runways with a torch cutter to turn into retaining walls 👍👍👍

Installed some 16’ 2x8 T&G over this 48’ long patio cover to tie it all together. Smooth side down for a stained finish....
11/07/2018

Installed some 16’ 2x8 T&G over this 48’ long patio cover to tie it all together. Smooth side down for a stained finish. Next up, a little paint and some Rolled roofing for the water seal 👍👍👍 can’t wait to see the end result

A little more progress on this patio cover. Rolled all the joists , set a couple block lines, installed the facia... lit...
11/01/2018

A little more progress on this patio cover. Rolled all the joists , set a couple block lines, installed the facia... little bit of hardware to install and then it’s time for some T&G 👍


rebuild project we started on an existing patio cover. Setting beams today with my builders level. One of the better i...
10/26/2018

rebuild project we started on an existing patio cover. Setting beams today with my builders level. One of the better investments tool wise that I absolutely love using. The finished result is always 👌👌👌

Address

San Diego, CA

Telephone

(760) 477-3328

Website

Alerts

Be the first to know and let us send you an email when Shaun Hight Construction posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Shaun Hight Construction:

Shortcuts

Featured

Share

Category