What are the opening hours?

Monday 07:30 - 17:00 Tuesday 07:30 - 17:00 Wednesday 07:30 - 17:00 Thursday 07:30 - 17:00 Friday 07:30 - 17:00 Saturday 07:30 - 17:00

FINE JSC

Home
Vietnam
Ba Ria
FINE JSC

Directions Website

FINE JSC – Chế tạo cơ khí, kiểm định & chống ăn mòn cho dự án công nghiệp. Đối tác độc quyền Corrocoat tại Việt Nam & Campuchia.

FINE JSC – Fabrication, inspection & corrosion protection. Exclusive Corrocoat partner in Vietnam & Cambodia.

06/10/2026

How do you get more years out of a pipespool that has to resist chemical attack and abrasion inside, and the weather outside?

Corrocoat UK's answer, on a 1200/1000 mm pipespool from a Scottish power station: not one coating, but a system where every layer has a job.

Prep: blasted to Sa 2½, min. 50 μm profile, then blown down, swept and vacuumed.
Inside: Corroglass 600 at 750 μm DFT, cured and spark tested, then Armagel at 1,250 μm against chemical attack and abrasion.
Outside: Plasmet ZF, a surface tolerant epoxy with rust inhibitor, MIO and glass flake, plus a Corrothane AP1 topcoat for colour retention and weathering.

The result: the spool was prepared to go back to the client for many more years of active service.

We apply these Corrocoat systems in Vietnam and Cambodia as the sole authorized distributor and applicator. Pipework wearing out? Send us a photo (0826 58 3979 or [email protected]) and we'll tell you what we'd do.

(Source: Corrocoat case study and product data sheets.)

03/10/2026

Corrosion inside a pipe stays out of sight — until it shows up as a leak, a contaminated flow or an unplanned shutdown.

Water, crude oil, gas, fuel, chemicals — every medium attacks steel differently. That is why there is no "one coating fits all" for internal pipe protection.

🔧 Meet FINE's Internal Pipe Coater
✅ Spray head mounted on a wheeled carriage that keeps it centred in the pipe bore — full internal circumference coverage
✅ Pulled through the pipe by an automatic winch, with travel speed calibrated to the specified coating thickness
✅ Result: consistent film thickness from one end of the pipe to the other — no thin spots, no heavy build-up, in areas no brush or hand-held gun can reach properly

▶ Internal pipe coating at FINE JSC — selected for your service, executed in-house:
✅ Piping for water & wastewater, oil, gas, fuel and chemical service
✅ Coating system selected according to the transported medium, operating conditions and the client's specification
✅ Specialist Corrocoat systems available — FINE is the sole authorized distributor and applicator of Corrocoat (UK) in Vietnam & Cambodia
✅ Internal surface preparation with RotoBlast — working range DN150–DN700
✅ Coating workshop: 2,500 m², capacity 6,000 m²/month
✅ Coating QA/QC by FROSIO Level III inspectors, under an ISO 9001:2015 (DNV) quality system

📍 Track record:
• Bakheng Water Production Facilities, Phnom Penh (VINCI & PPWSA) — internal coating meeting potable-water requirements, surface preparation to SSPC-SP10/SP16
• Vessel Thiên Ưng 1 — pipe spools coated with Corrocoat Polyglass VEF

From blasting to final inspection under one roof: fewer handovers, tighter quality control, predictable schedules.

📩 Tell us your medium and operating conditions — FINE will propose the right internal lining system:
☎ Hotline: +84 (0)826 58 3979
✉ [email protected] | 🌐 www.finejsc.com

Our Commitment ⇒ Your Success

01/10/2026

⚙️ CLEANING WHAT YOU CAN'T SEE — THE HARDEST SURFACE TO PREPARE

A pipe's internal wall is one of the toughest surfaces to prepare properly: confined, dark, and — on smaller diameters — barely wide enough for equipment to reach. Poor internal surface preparation means coating failure, corrosion, and contamination risk long before a pipeline ever goes into service.

FINE JSC operates RotoBlast internal pipe cleaning systems covering a full working range from DN150 to DN700 — able to reach and blast-clean the internal bore of pipes down to just 150mm in diameter, to international surface preparation standards.

This capability has been demonstrated across real projects and pipe configurations:
✅ Long Thanh International Airport — fuel pipeline system
✅ Water treatment plant pipeline systems in Cambodia (PPWSA & VINCI projects) — internal coating to drinking-water standard
✅ Large-diameter bent pipe sections for Hải Hoàng Phát — covering the full DN150–DN700 range

From small-bore piping to large-diameter, bent sections, FINE's internal pipe cleaning capability delivers a clean, contaminant-free surface — the foundation for coating adhesion and long-term corrosion protection.

Need internal surface preparation for your piping project? Contact FINE JSC for a technical consultation.

Our Commitment ⇒ Your Success.

30/09/2026

⚓ WHEN YOUR VESSEL'S SEAWATER SYSTEM FAILS, THE CLOCK IS AGAINST YOU

For ship owners and marine operators, a corroded main condenser scoop pipe or a failing sea chest strainer isn't just a maintenance item — it's unplanned downtime, lost operating days, and a safety risk for every hour it stays unresolved.

In a recent offshore, marine & energy sector project (Singapore), a vessel needed urgent restoration across three critical systems:
✅ Main condenser scoop pipe (14.1m long, Ø1.8m) — rubber lining failed
✅ Sea chest strainers — required full restoration
✅ Marine growth preventive system tank — needed corrosion protection

Corrocoat's Polyglass Standard system — engineered for immersion, marine and aqueous environments — was applied across all three systems. The pipe relining was completed in 3 days (including 2 night shifts), and the strainer restoration in 3 days — all work completed safely, within the vessel's required timeframe, to the required quality standard.

Global case study from Corrocoat (UK). FINE JSC is the sole authorized distributor and applicator of Corrocoat in Vietnam and Cambodia.

Is your vessel or plant's seawater system due for an inspection — before it becomes a shutdown? Contact FINE JSC for a corrosion assessment.

Our Commitment ⇒ Your Success.

28/09/2026

🌬️ WIND TURBINES NEED CORROSION PROTECTION, TOO

A wind turbine heading to Maasvlakte on Rotterdam’s coast will face salty sea air every day. Corrocoat Benelux coated the first components of this 6-metre turbine with that exposure in mind:

✓ Surface preparation by blasting
✓ Plasmet ZF adhesive layer
✓ Corrothane AP1 topcoat for colour retention and weathering resistance

These are photos and project details from Corrocoat Benelux. FINE JSC is Corrocoat’s sole authorized distributor and applicator in Vietnam and Cambodia, ready to discuss suitable protection for exposed industrial steelwork.

Our Commitment ⇒ Your Success.

Source and photos: https://www.corrocoat.com/casestudies/wind-turbine-corrosion-prevention/

25/09/2026

⚠️ URGENT OFFSHORE REPAIR: 94 FL**GE FACES SAVED FROM CREVICE CORROSION

94 fl**ge faces (1"–8" ID) had developed early-stage crevice corrosion — a previous repair had already failed, and a shutdown risked production losses of up to $678,000 per day.

Corroserve (Corrocoat) delivered an in-situ repair, no shutdown needed:
✅ Vacu-blasting + abrasive blasting within containment
✅ Former plates & release agents for precise casting geometry
✅ Fl**ge faces rebuilt with Plasmet HTE — high compressive & tensile strength
✅ Completed on-site by a 4-person crew, zero disruption to live operations

Result: all 94 fl**ge faces restored in just 9 working days, passed nitrogen pressure testing, and back in service within 24 hours — avoiding losses of up to $678,000/day.

Global case study from Corrocoat (UK) — FINE JSC is the sole authorized distributor and applicator of Corrocoat in Vietnam and Cambodia.

Our Commitment ⇒ Your Success.

**geRepair

24/09/2026

🏗️ ANOTHER MILESTONE DELIVERED: 8-TON OVERHEAD CRANE HANDED OVER TO VINCI

FINE JSC has completed the fabrication, transport, installation, commissioning, load testing and handover of an 8-ton overhead crane for the Bakheng Water Production Facilities in Cambodia.

✅ Fabricated and finished at FINE’s workshop
✅ Transported and installed at site
✅ Commissioned and load-tested with client and consultant witnesses
✅ Handed over to VINCI on 18 September 2026

Thank you to the VINCI team and our fabrication and site crews for bringing the project to completion.

Our Commitment ⇒ Your Success.

22/09/2026

🌊 PROTECTING 1600MM BUTTERFLY VALVES AT A NUCLEAR POWER STATION

EDF Energy needed corrosion and cavitation protection for two 1600mm NB butterfly valves in continuous seawater cooling service at Torness Nuclear Power Station (UK).

Corrocoat (UK) applied a multi-layer system:
✅ Blades: Corroglass 600, min DFT 1500 microns
✅ Shafts: Corrocoat Armagel for abrasion & chemical resistance
✅ Valve bodies: multiple coats Plasmet HTE + Corroglass EB topcoat (total DFT 2500 microns)
✅ External surfaces: Plasmet ZF + Corrothane AP1 topcoat

Result: significantly extended service life for critical valves under constant seawater exposure, verified by full thickness and spark testing.

Global case study from Corrocoat (UK) — FINE JSC is the sole authorized distributor and applicator of Corrocoat in Vietnam and Cambodia.

Our Commitment ⇒ Your Success.

21/09/2026

⚙️ RESTORING A HORIZONTAL SPLIT CASE (HSC) PUMP CASING

A power-industry HSC pump casing needed full refurbishment and protective coating to restore corrosion resistance and structural integrity to strict industry standards.

Corrocoat (UK) delivered the solution:
✅ Rebate of split-face & suction/discharge fl**ges for precise mating surfaces
✅ Abrasive blasting + soluble salt testing for a clean, salt-free substrate
✅ Internal lining: Corroglass 600 Series, min DFT 1250 microns
✅ External coating: 2 coats Plasmet ZF + Corrothane AP1 topcoat
✅ Thickness & spark test at 17kV before reassembly

Result: the pump was reassembled, pressure-tested, and returned to service with extended operational life.

Global case study from Corrocoat (UK) — FINE JSC is the sole authorized distributor and applicator of Corrocoat in Vietnam and Cambodia.

Our Commitment ⇒ Your Success.

19/09/2026

🧪 RESTORING A 98% SULPHURIC ACID CONTAINMENT TANK AT A PULP & PAPER PLANT

The concrete base of a sulphuric acid storage tank at a pulp & paper plant had suffered severe acid attack from an acid-base reaction with ground moisture, causing repeated previous repairs to fail.

Corrocoat (UK) carried out the restoration:
✅ 40,000 psi high-pressure water jetting to remove the acid-contaminated concrete
✅ Salt removal and surface abrasion
✅ Structural rebuild using glass-fibre reinforced epoxy polymer concrete
✅ Plasmet AR3 topcoat — 3 coats, total thickness 40–48 mils

Result: the tank was restored to its original dimensions with long-term resistance to acid and alkali exposure.

Global case study from Corrocoat (UK) — FINE JSC is the sole authorized distributor and applicator of Corrocoat in Vietnam and Cambodia.

Our Commitment ⇒ Your Success.

Address

31 Nguyen Huu Canh Street, Long Huong Ward
Ba Ria
78116

Opening Hours

Monday	07:30 - 17:00
Tuesday	07:30 - 17:00
Wednesday	07:30 - 17:00
Thursday	07:30 - 17:00
Friday	07:30 - 17:00
Saturday	07:30 - 17:00

Website

http://www.finejsc.com/, https://www.corrocoat.com/

Alerts

Be the first to know and let us send you an email when FINE JSC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Want your business to be the top-listed engineering company in Ba Ria?