Decadesigns SOLAR

Decadesigns SOLAR Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Decadesigns SOLAR, Solar Energy Service, Corner Paisley/Lyton Workington, Harare.

DECADESIGNS SOLAR has established itself as an undisputed regional industry leader in distribution, installation and after sales services and providing a globally competitive package of products and expertise.

For all your solar products and back up power installations.
30/08/2021

For all your solar products and back up power installations.

Save Electricity and pump water using solar pumps. We have different packages which suits your specifications.   from th...
14/06/2021

Save Electricity and pump water using solar pumps. We have different packages which suits your specifications. from the sun.

Purchase your home solar set and Light up your home  ngaibake!!!!!
10/05/2021

Purchase your home solar set and Light up your home
ngaibake!!!!!

Ten-Tips  to use the power from your solar modules most effectively. In a home there are many opportunities for self-con...
30/10/2020

Ten-Tips to use the power from your solar modules most effectively.

In a home there are many opportunities for self-consumption from the power of your solar panels on your rooftop.

If you have installed solar modules on your roof, your garage, your carport or at ground level on your property, you will require less electricity from the power grid. Here you will find tips on how you can use most of this valuable resource for your own needs.
Deciding to put up a PV installation signifies a rethink. Whereas so far the electricity has been coming from the grid, it is now produced on your own property, much less expensive than the grid power. Therefore: Use as much of the solar electricity yourself and if yu have the option feed as little as possible back into the grid.
I will show you how it is done.

These are the 10 expert tips to use solar electricity.

1. Reduce the electricity consumption of the building!

First of all: If you want to save on electricity costs – with or without PV – you should first eliminate devices and appliances that use too much of it. These include standby devices, incandescent light bulbs and water heaters. The lower your overall consumption, the greater the part of it that you will be able to cover using solar PV.

2. Install LEDs instead of light bulbs!

Usually the largest single cost factor is lighting. Obsolete light bulbs only use about ten percent of the electricity to make light. 90 percent are lost as heat. They produce heat rather than light, because they are based on a glowing filament made of tungsten. Modern LEDs use almost all of the electricity to make light. You can clearly notice this from the fact that they stay cool, i.e. there is much less loss. A good LED needs about a tenth of the electricity to produce the same amount of light. And because it does not heat up so much, it lasts much longer. And: The price of LEDs has come down so much, that exchanging them for regular light bulbs pays off within one or two years. The same is true for industrial lighting systems which often use mercury vapour lamps. These, too, use up a lot of electricity and can easily be replaced by LEDs.

3. Turn off standby mode!

Many electrical devices (kitchen appliances, TVs, computers, game consoles, HiFi systems) also consume electricity when they not in use and on standby. Considering the number of electrical devices in a normal house, the standby consumption can really add up. For that reason, such devices should – when not in use – be physically separated from the circuit by using switchable sockets.

4. Make hot water electrically!

If you are producing solar electricity, you should convert your hot water systems to electric boilers. Instantaneous water heaters also allow the heating of water close to the tap – for instance as under-sink units. The water temperature can be adjusted to exactly what is desired. The demand for hot water is more or less the same over the course of the year. During the late spring and summer, that demand can entirely be met by solar power. That increases the level of self-consumption. A combination with special hot water heat pumps can also make sense.

5. Run high-consumption devices during the day!

Those appliances in the household with the highest electricity demand are the dish washer, the washing machine, the tumble dryer and the kitchen stove. These can easily be equipped with timer switches, so that they run during the day, when the solar panels on the roof is producing a lot of output, which can be used directly. A high-wattage stove might be a challenge for PV by itself. In this case, a large storage unit (solar battery) can be used as a buffer for short-term load peaks. Because it is not just the number of kilowatt hours on the roof that has to be sufficient, but also the currents made available at short notice. This determines if a battery storage unit is designed for capacity (in kilowatt hours) or output (in kilowatts).

6. Do your gardening on solar electricity!

Solar electricity yields are highest between spring and autumn. This is also the time of year when the garden requires the most work. You can very conveniently run electric lawn mowers, hedge trimmers or lighting off solar electricity. If you have a solar battery, you can use it to power LED lights in your garden in the evening and at night. A garden sauna can be heated up using surplus electricity during the day, so that it is ready for use in the evening.

7. Heat electrically during the transitional periods!

If your solar system is run in combination with a sufficiently large battery storage unit, you can use infrared radiators to take the chill out of cooler evenings. Such radiators come in a variety of nice designs, even in the form of bathroom heating mirrors. As long as they only use little power and are only used for additional heating, they are a good way to use up solar electricity. Once the electric heating from solar power no longer suffices, you will have to buy in electricity from the grid. Or you switch to a more efficient thermal heat pump system.

8. Energy storage increases efficiency!

In Zimbabwe early 2014 and 2019 the price of stationary lithium batteries has fallen by more than 40 percent. This trend is expected to continue. Furthermore, the end of February saw the introduction of a new funding programmes from banks that will continue until 2022.These are good reasons for investing in a solar battery storage .What size to choose depends on the building’s electricity demand and the size of your solar panels.Lithium batteries currently cost about usd$385 per kilowatt hour, Gel batteries about usd$ 350 to usd$500 (net prices for end customers). However: In a private residence, having a battery storage unit without a solar panels makes very little sense. This can be different for commercial enterprises.

Without energy storage, you can make good use of about 50 to 80 percent of the solar electricity for your own house. A battery can easily take that up to (almost) 100 percent. If you do not base the own consumption just on the solar panels ,but on the electricity demand of the entire house, the following general rule applies: Without battery storage, you can meet about 30 to 50 percent your electricity demand directly from solar. In combination with a solar battery, this can be as much as 90 percent. To meet your entire electricity needs over the course of a year, you need a second generator, e.g. a cogeneration unit. It is usually simpler – and less expensive – to use the power grid.

9. Switch to e-mobility!

Almost as useful as solar batteries can be electric cars and vehicles – of any size. From the lawn mower to grandpa’s (or the friendly neighbour’s) electric wheel chair to pedelecs (e-bicycles) and e-scooters for the family. All of these contain lithium batteries which can conveniently be charged with solar electricity. Ultimately, there is the small electric car that can be used to go shopping, for short trips or to commute to work. For it is especially such frequent short trips that use up a lot of the fuel budget of conventional cars.

10. Treasure hunt for all your family!

Experienced Engineers & technicians can support you when it comes to consumption of solar electricity. It can be helpful to go step by step and check your metres to see what effect each measure is having. Finding the devices in your house which use up the most electricity can be like a treasure hunt, so make a game of it and let your kids go exploring. The money you save can be put aside and used to have a solar powered party with your neighbours. Or a holiday to Vicfalls or other resort towns .

Written by
Eng L.R Mwale
(Msc Electral Power Systems)
(Pr.Eng ,M.Zwe.I.E & MIEEE)

Facebk Page:Decadesigns Solar
www.decadesigns.co.zw

Cable termination of the Array.
20/10/2020

Cable termination of the Array.

Commissioning an 12 x 370Watts Panel Array.
20/10/2020

Commissioning an 12 x 370Watts Panel Array.

Techniques to Maximize Solar Panel Power OutputThe output current of a solar panel varies nonlinearly with the panel vol...
18/10/2020

Techniques to Maximize Solar Panel Power Output
The output current of a solar panel varies nonlinearly with the panel voltage. Under short-circuit conditions the output power is zero since the output voltage is zero. Under open-circuit conditions, the output power is zero since the output current is zero. Most solar panel manufacturers will specify the panel voltage at maximum power (VMP). This voltage is typically around 70 – 80% of the panel’s open circuit voltage (VOC).
Ideally, any system using a solar panel would operate that panel at its maximum power output. This is particularly true of a solar powered battery charger, where the goal, presumably, is to capture and store as much solar energy as possible in as little time as possible. Put another way, since we cannot predict the availability or intensity of solar power, we need to harness as much energy as possible while energy is available.

Visit our page:Decadesigns Solar for more infor.

11/10/2020

LESSON 4
Techniques to Maximize Solar Panel Power Output
The output current of a solar panel varies nonlinearly with the panel voltage. Under short-circuit conditions the output power is zero since the output voltage is zero. Under open-circuit conditions, the output power is zero since the output current is zero. Most solar panel manufacturers will specify the panel voltage at maximum power (VMP). This voltage is typically around 70 – 80% of the panel’s open circuit voltage (VOC).
Ideally, any system using a solar panel would operate that panel at its maximum power output. This is particularly true of a solar powered battery charger, where the goal, presumably, is to capture and store as much solar energy as possible in as little time as possible. Put another way, since we cannot predict the availability or intensity of solar power, we need to harness as much energy as possible while energy is available.
There are many different ways to try to operate a solar panel at its maximum power point. One of the simplest is to connect a battery to the solar panel through a diode. This technique is described here in the article "Energy Harvesting With Low Power Solar Panels". It relies on matching the maximum power output voltage of the panel to the relatively narrow voltage range of the battery. When available power levels are very low (approximately less than a few tens of milliwatts), this may be the best approach.
The opposite end of the spectrum is an approach that implements a complete Maximum Power Point Tracking (MPPT) algorithm. There is a variety of MPPT algorithms, but most will have some ability to sweep the entire operating range of the solar panel to find where maximum power is produced. The LT8490 and LTC4015 are examples of integrated circuits that perform this function. The advantage of a full MPPT algorithm is that it can differentiate a local power peak from a global power maximum. In multi-cell solar panels, it is possible to have more than one power peak during partial shading conditions .Typically, a full MPPT algorithm is required to find the true maximum power operating point. It does so by periodically sweeping the entire output range of the solar panel and remembering the operating conditions where maximum power was achieved. When the sweep is complete, the circuitry forces the panel to return to its maximum power point. In between these periodic sweeps, the MPPT algorithm will continuously dither the operating point to ensure that it operates at the peak

In summary, many different ways of operating a solar panel at its maximum output operating condition exist. The panel can be connected to a battery (through a diode) whose voltage range is close to the maximum power voltage of the panel. A full MPPT algorithm, including periodic global sweeps to find the global maximum and a continuous dither to remain at that maximum (an example is the LT8490), can be used. Other products implement an input voltage regulation technique (MPPC) to operate a solar panel at a fixed operating voltage including the LTC3105, LTC3129, LT3652 (HV), LTC4000-1 and the LTC4020.
Compiled by Eng L.R. Mwale
(M.Zwe.I. E, Pr.Eng & MIEEE)
Like & Follow Our Face book Page: Decadesigns Solar
For more Educative Lesson 5.

Lesson 3Rated maximum POWER (Pmax) Of Solar Panel as a Parameter.You may hear your solar installer say, “it’s a 255Watt ...
30/08/2020

Lesson 3
Rated maximum POWER (Pmax) Of Solar Panel as a Parameter.
You may hear your solar installer say, “it’s a 255Watt panel” or “the panel I am recommending has a wattage of 300Watts.” Or, when you are reading a quote from a solar installer, you might see numbers like 245W, 300W.
As well if you check at the back of your Solar Panel just before those guys install your system, they are a lot of confusing numbers there.
Today we are discussing one of the numbers called (Pmax) at the back of your Solar Panel.
Rated maximum POWER (Pmax): Refers to a solar panel’s wattage, capacity and power output.
Size vs. Quantity: Typical Solar Panel Ratings and Capacity
When buying Solar Panels power output on its own is not a complete indicator of a panel’s quality and performance characteristic. For some panels, their high power output rating is due to their larger physical size rather than their higher efficiency or technological superiority.
For example, if two solar panels both have 15% efficiency ratings, but one has a power output rating of 250 watts and the other is rated at 300 watts, it means that the 300-watt panel is about 20 percent physically larger than the 250-watt panel. That’s why Decadesigns Solar and other industry experts view panel efficiency as being a more indicative criterion of solar panel performance strength than solar capacity alone when making a selection.
In practical terms, a solar panel system with a total rated capacity of 6kW (kilowatts) could be made up of either 24 x 250-Watt panels or 20 x 300-Watt panels. Both systems will generate the same amount of power in the same geographic location. Though a 6kW system may produce 7,000 kilowatt-hours (kWh) of electricity every year in Harare, that same system may produce 9,000 kWh every year in Gweru because of the amount of sun each location gets each year.
The electricity generated by a solar PV system is governed by its rated power output (Pmax of Solar Panels), but it’s also dependent on other factors such as
1.panel efficiency
2.temperature sensitivity,
3. degree of shading that the system experiences
4. and the tilt angle and azimuth of the roof
As a general rule of thumb, it makes prudent financial sense to install a solar system with as much power output as you can afford (or that your roof will accommodate).
Compiled by Eng L.R, Mwale
(MZwe.I. E, MECZ & MIEEE)
Like & Follow Our Face book Page Decadesigns Solar
For more Educative Lesson 4.

Lesson.2I will continue shedding more light on the confusing solar panel parameters or specifications written at the bac...
27/08/2020

Lesson.2
I will continue shedding more light on the confusing solar panel parameters or specifications written at the back of the Solar Panel and their importance.

Short-circuit current (Isc)
The electrical circuit needs to be complete for flow of current. In solar system, when you switch on the AC side home supply ie some load (resistance) is detected. In an ideal condition, when the voltage is Zero then maximum current will flow in the circuit. In this case the current is called as short circuit current.

The short-circuit current is the current through the solar cell when the voltage across the solar cell is zero (i.e., when the solar cell is short circuited).

Honestly speaking this is just an “ideal condition”-never exists or rarely exists.
But this ideal condition is needed to safe guard the down stream equipment like solar charger controllers and it has been adopted as a standard when rating solar panels.
“In other words its an assumed worst case scenario”
Or its a “what if” condition.

Thank you.

Lesson 1.If you check at the back of your solar panel there is a silver-whitish paper applied at the right or left hand ...
24/08/2020

Lesson 1.
If you check at the back of your solar panel there is a silver-whitish paper applied at the right or left hand corner.
This paper has what we call the specification of your solar panel or its rating.There are a lot of numbers written on that paper which can be confusing.We are going to explain each of them to help clear it up & understand.

Open Circuit Voltage (Voc)
Open circuit voltage is how many volts the solar panel outputs with no load on it. If you just measure with a voltmeter across the plus and minus leads, you will read Voc. Since the solar panel isn’t connected to anything, there is no load on it, and it is producing no current.

This is a very important number, as it is the maximum voltage that the solar panel can produce under standard test conditions, so this is the number to use when determining how many solar panels you can wire in series going into your inverter or charge controller.

Voc will potentially be briefly produced in the morning when the sun first comes up and the panels are at their coolest, but the connected electronics haven’t woken up out of sleep mode yet.

Remember, fuses and breakers protect wires against over-current, not over-voltage. So, if you put too much voltage into most electronics, you will damage them.

Thank you for today's lesson

Eng L.R Mwale

whats up:0772566112

Address

Corner Paisley/Lyton Workington
Harare

Alerts

Be the first to know and let us send you an email when Decadesigns SOLAR posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Share