KewFab

www.kewfabmotorsport.com

28/10/2026

Ben Molesworth Rover P4 roll cage

Nice and basic 6 point roll cage, leaving access for the handbrake lever and also to allow for the sun visors to still be used.

Roll cage tubing supplied by ProFormance Metals

15/10/2026

Michael and Jack Bennett e36 - bigger gearbox tunnel. Slightly scary job to begin with as this is the first one that I’ve done but lots of trimming and checking later and we have a nice big gearbox tunnel to give plenty of space for the gearbox and a nice flat surface to mount things on. We marked out the original gear selector hole but left it in drilled in case Michael wants to move the position and can decide what size hole is required depending on the shifter

15/10/2026

Michael and Jack Bennett e36 - tube front end with removable bash bar and upper support bar for maximum access. Making use of my new laser level to make life easier 😂

14/10/2026

Michael and Jack Bennett e36 - next up was the rear firewall. Keeping easy access to the rear shocks as one of the priorities we kept them behind the firewall so that they can be accessed through the rear opening rather than having to climb through the car or remove a rear window to get to them

The lower outer sections we left plain so that they can be drilled for water/fuel lines and wiring loom to pass through if needed when Michael has decided on routing for these

13/10/2026

Michael and Jack Bennett e36 - next was the tube rear end and fibreglass clamshell. Basic single hoop structure with jacking point. Michael asked for no bash bars to be added on this one to give is a clean look as he might leave it with no rear bumper but the bash bars can easily be added at a later point

We also added some AN -16 fittings for the radiator inlet and outlet and welded on some m8 bosses to mount it

For the lower boot lid mounts, we used some 8mm round bar to mount some push clips, the idea behind this is to hopefully allow for some flex incase of a rear end knock to try and limit damage to the fibreglass boot lid

12/10/2026

Michael and Jack Bennett e36 - we then made some mounts for the Nuke Performance fuel cell to sit on. We looked at a few different options for the fuel cell position but wanting to keep the radiator behind it so that it wasn’t blowing hot air on the fuel system and also keeping access to the diff as easy as we could, this was the option we went for

09/10/2026

Michael and Jack Bennett e36 - started with the roll cage, we also had to work out the radiator and fuel cell position before the rear subframe bracing and rear stays

We left the main hoop diagonal and harness bars out until we had finished the firewall to give easier access to do this and then added those after the firewall was finished

Roll cage tube supplied by ProFormance Metals

08/10/2026

Michael and Jack Bennett e36 coupe shell finished off last week, lots of fab work done on this one so I will upload it in sections

ProFormance Metals supplying the tube as always

24/09/2026

Astra TRW electric hydraulic power steering pump bracket made for my e46

02/09/2026

I’m looking to sell on everything to produce the Land Rover discovery 2 td5 snorkel and airbox kits.

This will include everything from jigs, cad files, cut dimensions, notes and photos of production and fitting. I can also advise on material suppliers and with how I put these together. I can also give you a breakdown on numbers for this product and I can also draw up a logo tag for your business to go in place of the Kewfab logo plate

This was originally developed for a friend and then after getting asked to do a few more, I made the jigs etc. This product sells well but as off road fabrication isn’t my forte, I think this would be better suited to a fabricator/business that is more focussed on off road.

This will hopefully also free up some time and funds to put into the development of some other products that I’d like to get on with which are better suited to Kewfab. I have no intention on carrying on producing these after the sale and any inquiries I can get I can pass on

If anyone knows of any businesses or fabricators that would be interest in this, tag them or ask them to give me a message and I can go through details with them and discuss pricing etc

Address

Ellesmere Port

Website

http://www.kewfabmotorsport.com/

Alerts

Be the first to know and let us send you an email when KewFab posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.