Philspeed Engineering

Philspeed Engineering High performance engine building and vehicle modifications. ECU Remapping, engine balancing.

*****Impact to modified cars*****Below is a government consultation on making vehicles meet the EXACT emissions level th...
30/08/2026

*****Impact to modified cars*****
Below is a government consultation on making vehicles meet the EXACT emissions level that it left the factory with or it will fail, despite passing an MOT.
This is another part of their plan to force vehicles off the road and it will affect everything before 2016, I believe. This is huge, and EVERYONE needs to fill this out. It takes 10 mins, possibly less, because as soon as you state you’re opposing it, they allow you to skip to the end because the other 20 questions are all about supporting it (a telling story in itself!).

Please do not just ignore this.
the road and it will affect everything before 2016, I believe. This is huge, and EVERYONE needs to fill this out. It takes 10 mins, possibly less, because as soon as you state you’re opposing it, they allow you to skip to the end because the other 20 questions are all about supporting it (a telling story in itself!).

Please do not just ignore this.
(Taken from another page)

https://www.gov.uk/government/consultations/in-use-emissions-of-road-vehicles-regulating-environmental-impacts/regulating-environmental-impact-of-in-use-emissions-of-road-vehicles?fbclid=IwdGRjcAUAu9hwZG9mBWZkaWQWUNfoOuUsnYi67GB8TJj32p465ir_GGV4dG4DYWVtAjExAHNydGMGYXBwX2lkCjY2Mjg1NjgzNzkAAR7-sZ4LWa5m3QET7rNmGWhsWtf4xn5k3TF4YZJURy-dxDnT5D8kUzp0I8GNzQ_aem_bPRBxrhUJXVWM4AV-Ame3A

We’d like to set additional cookies to understand how you use GOV.UK, remember your settings and improve government services.

Exhaust downpipe now finished apart from some heatwrap. Clearances are a little tight with a 3" system 😬
23/08/2026

Exhaust downpipe now finished apart from some heatwrap. Clearances are a little tight with a 3" system 😬

18/08/2026

Apologies to anyone who has had difficulty getting hold of me recently but I currently have virtually no phone or data signal at my workshop. Apparently there's an issue with a phone mast nearby 🙄

17/08/2026
Project Boxster Mongrel was originally a Tiptronic but I have converted it to manual transmission. This is the clutch ha...
05/07/2026

Project Boxster Mongrel was originally a Tiptronic but I have converted it to manual transmission. This is the clutch hard line that runs from halfway along the left sill to the gearbox. Unfortunately the first time i tried to depress the clutch it burst the metal coil at the slave cylinder due to corrosion. This section of pipe was a fortune 🤑 from Porsche but with a little help from Resto Shack in Exeter we've managed to fit an Audi slave connection to the Porsche line. 😎👌

Boxster S front bumper with the middle radiator inlet which I'll be using for the charge cooler radiator.
04/07/2026

Boxster S front bumper with the middle radiator inlet which I'll be using for the charge cooler radiator.

Turbo Boxster project is progressing slowly 🙄Finally got it running yesterday so now on to the exhaust,  cooling system ...
31/05/2026

Turbo Boxster project is progressing slowly 🙄
Finally got it running yesterday so now on to the exhaust, cooling system and charge cooler set up. 😀

Address

Newton Abbot

Opening Hours

Tuesday 9am - 5pm
Wednesday 9am - 5pm
Thursday 9am - 5pm

Telephone

+447521715108

Alerts

Be the first to know and let us send you an email when Philspeed Engineering posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Share