Gmd sons sluice valves lahore Pakistan

Gmd sons  sluice valves lahore Pakistan Incorporated in 1936 we are the oldest manufactures of Sluice valves Gate valves Check Valves

13/05/2026
Our class PN 16 threaded SS or bronze valves And 220 volt Solonoid Valves
13/04/2026

Our class PN 16 threaded SS or bronze valves And 220 volt Solonoid Valves

Our Cast iron fl**ged Foot valves.Absoloute high class
12/03/2026

Our Cast iron fl**ged Foot valves.Absoloute high class

Pillar hydrant Mild steel
18/02/2026

Pillar hydrant Mild steel

*GMD TUTORIAL*The image provided is an illustration detailing a segment of a Drainage Waste and Vent (DWV) plumbing syst...
11/12/2025

*GMD TUTORIAL*
The image provided is an illustration detailing a segment of a Drainage Waste and Vent (DWV) plumbing system as it is typically installed within the framing of a wall and floor structure. It shows how a smaller drain line (likely from a sink or tub) connects to a larger main drain or stack.
Here is a detailed breakdown of the components and connections shown:

DETAILED DESCRIPTION OF THE PLUMBING DIAGRAM SEGMENT

1. STRUCTURAL CONTEXT
* Framing: The top of the image shows standard wood framing including a bottom plate resting on the floor and vertical studs forming a wall cavity.
* Piping Material: The main stack and large drain components appear to be illustrated in copper (or a copper-colored material) while the smaller connecting fittings are white plastic (likely PVC or ABS) which is common in DWV systems.

2. THE MAIN DRAIN/STACK (RIGHT SIDE)
* Large Vertical Pipe: A wide copper-colored pipe is shown coming up from the floor likely forming the main drain stack or a principal branch drain.
* Flange/Opening: The top of this pipe has a wide flared opening or fl**ge (partially labeled "Closet bend" or similar although not fully visible) indicating it is a connection point for a large fixture most commonly a toilet (water closet).
* Horizontal Line: The larger copper-colored pipe continues horizontally along the floor acting as the main drain line.

3. THE SMALLER DRAIN LINE (LEFT SIDE)
This section shows the connection of a smaller vertical drain pipe (likely from a fixture on an upper floor or a sink/tub drain) to the main horizontal drain:
* Vertical Pipe (Copper-Colored): This pipe runs vertically down through the bottom wood plate indicating it is connected to a fixture above.
* Elbow (White Fitting): A white plastic elbow connects the vertical pipe to the next fitting.
* Street 45 Y (White Fitting): This is a specific type of Y fitting.
* Y Fitting: Used to join two drain lines at an angle that encourages smooth flow (prevents clogging) typically a 45° angle.
* Street: Means one end of the fitting has a spigot (or male) end that is sized to fit *inside* another fitting's hub (female) end which saves space and reduces the number of connections.
* 45: Indicates the angle of the branch.
* 3x2 Reducing Y (Copper to Copper Connection):
* This is the final fitting that connects the smaller branch line (coming from the 45 Y) into the larger main horizontal drain pipe.
* Reducing: The label suggests this fitting reduces the diameter from the larger main drain pipe (e.g. 3 inch) down to the size of the branch pipe (e.g. 2 inch) where the connection is made. The drawing shows the branch entering the Y fitting which then connects to the horizontal line. This Y must be a Wye fitting (or combination fitting) to ensure the branch enters the main drain at a non-turbulent angle (sloped in the direction of flow).

4. COUPLINGS/CONNECTIONS
* Brass-Colored Rings: Multiple brass-colored rings are shown connecting sections of the copper-colored pipe. These represent couplings or hubs where one section of pipe is joined to another likely using a soldered connection for copper pipe or a solvent-welded connection for plastic pipe (if this were a conceptual drawing using copper color for all drains).

ILLUSTRATED PLUMBING PRINCIPLES
This diagram emphasizes the following essential DWV rules:
1. Directional Flow: All connections are made using Y or combination fittings (not sanitary T fittings on

14" dia Class PN 10 Check Valves delivered today 10th December 2025
10/12/2025

14" dia Class PN 10 Check Valves delivered today 10th December 2025

14" Dia os&y Class 10 gate Valves delivered today 10th December 2025..
10/12/2025

14" Dia os&y Class 10 gate Valves delivered today 10th December 2025..

Cast Iron/Ductile Iron Os&y class PN 20 gate valve. Test pressure 400 lbs PSINote* PN 20 gate valves are similar in dime...
08/11/2025

Cast Iron/Ductile Iron Os&y class PN 20 gate valve. Test pressure 400 lbs PSI
Note* PN 20 gate valves are similar in dimensions to PN 16:Valves but are tested at 400lbs to 450lbs PSI

Material ready for a world bank project in southern Punjab.Today 7th November 2025" Ground Hydrants as per BSS 750""Pade...
07/11/2025

Material ready for a world bank project in southern Punjab.Today 7th November 2025
" Ground Hydrants as per BSS 750"
"Padestal Pillar Fire hydrants as per BSS 336"

OUR MONO BLOCK PUMPS 3" TO 8" SIZE
29/10/2025

OUR MONO BLOCK PUMPS 3" TO 8" SIZE

Address

6 Rehman Gali Railway Road Lahore
Lahore
54000

Alerts

Be the first to know and let us send you an email when Gmd sons sluice valves lahore Pakistan posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Share